Pressure Washer Operation
chuckles
Join Date: Jul 2003 Posts: 88 Eastern PA Pics |
2003-07-01 58651
OK, so now I have this really great washer like the other Father's day buyers. So I think we should get some do and don'ts:
1) How do I remove the green mold off my house siding if it says don't put bleach through the pressure washer???
2) What is the right nozzle for each job:
a) washing the car
b) Doing cedar siding 6" lap
c) Cedar decking
d) cleaning concrete
3) what would you use that nozzle that has the tight pattern on?
I used the middle nozzle to clean the garage floor that had a failing epoxy finish on it and it cleaned it pretty good and removed alot of the loose paint without any chemicals. Also got rid of the glaze that the tires leave, making it look ready for a new paint job.
What are you guys doing?
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
kwschumm
Join Date: Feb 2003 Posts: 5764 NW Oregon Pics |
2003-07-01 58662
I think the only rule is to use the least force necessary to do the job. It's all to easy to do damage by removing paint, shredding wood fibers, blasting stones out of exposed aggregate concrete, blowing water past seals, etc.
When cleaning concrete I always use a turbo nozzle at low pressure and work the pressure up until it starts to get clean. With a high pressure unit it's possible to etch concrete.
When using a pw that doesn't have adjustable pressure I start with the widest nozzle available and hold the wand a fair distance from the surface then slowly move in until it starts doing the job. If the surface isn't getting clean I switch to the next smallest nozzle, and repeat this procedure until I start getting good results.
....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
Chief
Join Date: Jul 2003 Posts: 4299 Southwest MiddleTennessee Pics |
2003-07-03 58779
I am using the 60 degree nozzle the most. It is the least destructive but cleans well. Cleaned my 4410 with it, the trash cans, recycle bins, oil spots in the drive (made by the wife's Ford, the Cummins and Nissan are neat parkers) I plan to strip the loose paint from the house so I can paint. Also still need to clean the Sea Ray. Not going to be using it on windows, but I may experiment with low pressure. I agree, use the lowest pressure and widest angle nozzle possible and gradually work your way up. Real happy with mine so far. ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
plots1
Join Date: Jul 2003 Posts: 563 mo Pics |
2003-07-03 58791
I agree to to start with wide nozzle and work to narrower as needed. the narrow ones can do more damage than good if not careful. been happy with mine thusfar, between me and the wife we cleaned everything. ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
DRankin
Join Date: Jan 2000 Posts: 5116 Northern Nevada Pics |
2003-07-03 58805
Kwschumm, That is also the rule a wise policeman follows.
Use the least amount of force.... ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
chuckles
Join Date: Jul 2003 Posts: 88 Eastern PA Pics |
2003-07-04 58819
Topic Starting a pressure washer:
I have the Home Depot Commercial grade 2700 washer with the crankshaft pump.
The starting instructions say to release the gun pressure after the first two pulls or you won't be able to spin the engine.
I have found that the only way to start it is to hold the trigger of the gun while pulling the starter cord, then it starts right up, no problem. ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
plots1
Join Date: Jul 2003 Posts: 563 mo Pics |
2003-07-04 58822
Chuckles, my xr2700 has to be started the same way. ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
chuckles
Join Date: Jul 2003 Posts: 88 Eastern PA Pics |
2003-07-04 58825
Plots,
Remember I had that problem with the pump filler plug on the X2750? Well I went back to the depot and they have about 8 or 9 returned XR2750 all with a completely different plug than I got with the two I returned, screws in perfectly, go figure! Must have been a plug that some line guy should have put on one of their smaller units.
One thing I am wondering is if I can substitute a 50 foot 3/8" hose for the 25 foot 5/16th that comes with it. The 25 foot extension at Depot is $49.99, and then I have that connection in the middle that can leak or snag on things. Does using 3/8" hose screw things up ?????
....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
plots1
Join Date: Jul 2003 Posts: 563 mo Pics |
2003-07-04 58827
mine offerd an extension hose with a mail in offer for free. still waiting, and mine is the XR2750 not a 2700 ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
Chief
Join Date: Jul 2003 Posts: 4299 Southwest MiddleTennessee Pics |
2003-07-04 58830
chuckles, I would think the larger inside diameter hose may lower the spray pressure a bit but should work ok. ....
Reply to | Quote Reply | Add Photo
Pressure Washer Operation
WillieH
Join Date: Feb 2003 Posts: 543 New England Pics |
2003-07-17 59652
chuckles -
This is one of the luxuries of having an adjustable pressure washer pump pressure control valve. As operating parameters change, such as a larger i.d. hose, longer hose, different size nozzles, etc., one can adjust the PCV to offset the difference in output pressure, to the same operating pressure as if one was still using the smaller i.d. hose, nozzle, or longer/shorter length hose.
Willie H. ....
Reply to | Quote Reply | Add Photo
Go Top
Share This