Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

you Really don't have a Massey-Ferguson tractor your tractor says Massey-Ferguson but it is an Iseki made in japan.Not sure about Parts or linkage.

japan,china,India tractor I try to stay away from..
I rather have an low hour older Massey-Ferguson or a Ford tractor then these foreign made tractors that you can't get parts or anyone to work on them.

A 2 Series Massey-Ferguson tractor is the best I think like a 230,235,240,250,255.Etc.
I have a 250 m-F for sale with about 1295 actual hours price is $8750.00 diesel a very good tractor ,I'm the 2nd owner.

Massey Ferguson 1429 Tractor 1429 will not shift into 1st or 2nd
Massey Ferguson Tractors
Replies 4 Post by 46bugs

I filled my hydraulic sump to the point where fluid just reached high enough to wet the bottom of the dipstick. But threaded Asian dipsticks should not be screwed back into the hole for a level check. Unscrew, wipe, set back ON the hole, remove, check level. Checking the level ON the hole rather than IN the hole will partially solve the mystery of the missing fluid. The rest is likely in the lines and cylinders.

Also, never lower hitch or FEL before shutting off the engine. Doing so will push fluid back to the sump, possibly overfilling it to the point of spillage out the vent plug. Lower hydraulics, shut off engine, THEN check levels.

Front drive uses same GEAR OIL as transmission & rear end. But you should only fill it to the point the axle shafts are submerged. You should drain some out, or you'll develop leaks. Don't just top up and forget though, as it takes a while for the thick gear oil to flow into the outboard drives. Check again in after about an hour of driving the tractor, and top up as necessary.

Transmission & rear end should have marks on the dipstick. Same thing; remove, wipe, set in hole, check level, adjust as required.

Hydraulic sump has a drain. Front end has a drain, transfer case has a drain, tranny has a drain, as does the rear end. Some variants even have a 2nd rear end drain. And again, if/when topping up tranny/rear end, work the tractor for a while and check levels again.

//greg//

Nortrac 204C Tractor no markings on dip stick
Jinma Farmpro Agracat Nortrac
Replies 2 Post by greg_g

I change my anti freeze every 2 years also flush the radiator at that time. They are not made as the old radiator was.

Oil change ,filters ,anti -freeze is cheaper then an overhaul or a bad radiator.I believe in maintenance. Grease is cheaper then a joint or a new front end.or a u-joint.

Tractor Fluids and Lubrication Recommendations
Cub Cadet
Replies 17 Post by 46bugs

Here is a pic of mine... <br>
<br>
From the manual:<br>
<br>
Theory of Operation:<br>
Current flows from the battery through F1 fusible link (Red Wire) into the<br>
key switch. With key switch in the start position current<br>
flows through the key switch, through jumper 401 Yel/Red,<br>
then back through the key switch to the neutral start switch(Purple Wire).<br>
With transmission in neutral, current activates the starting<br>
motor solenoid.<br>
High current from the battery flows across the solenoid<br>
contacts to operate the starting motor.<br>
<br>

need wiring diagram
Utility Vehicles UTV/ATV
Replies 2 Post by Izera21

Izera21 has posted a new photo.

Subject: Gator 4x2 Switch.

Description: <br>Gator start switch

Gator 4x2 Switch - New Pix by Izera21
Photos
Replies 1 Post by Izera21

The 187 is rated at 661 lbs at the pins and 529 lbs 24" behind. I would guess the 165 would be a 100 lbs or so less. Just a guess.

Are there specs availalble for the lifting capacities of 3pt hitches
Yanmar Tractors
Replies 3 Post by winston1

I have an 05 Cub 7532 hydrostatic.<br>
<br>
The range select lever is not working. It was popping out of high, then when in a neutral location was in mid gear. Finally it stopped working at all and tractor appears to be in neutral. Took lever apart and shaft appears to be turning to inside of tranny. Anyone have expoerience with this? Any other reasons I may be missing that cause this problem? <br>
<br>
Thanks in advance

7532 Transmission issue - anyone have experience
Cub Cadet
Replies 1 Post by ccrider11

Mabutler,

The B2400 would be a far better choice for you, but with 20 acres you should really be looking for something even larger than the B2400. Maintaining 20 acres would be a bit too much to ask of either of these tractors.

Given the choice between the two, the B2400 would be my pick. The larger tires on the B series tractors make for a much better ride over rough ground.

The best part......the B series tractors have a full size category 1 3-point hitch, meaning that you could easily find implements to match. The BX tractors have a smaller 3-point hitch, requiring special implements that aren't easy to find. Used Cat1 implements are available at auction for little or nothing. You could easily fit your B2400 up with a used rear blade, rake, cultivator, plow, mower, etc. Not so easy to do with the BX tractor.

However, I'd be looking for something slightly larger, such as a Kubota L Series with about 40 horses.

Hope this helps.

Joel

Advice please BX2360 500 hrs vs B2400 1 000 hrs
Kubota Tractors
Replies 5 Post by candoarms

Hello,<br>
First time on Tractorpoint. I have a HPX Gator 4x4 gas.<br>
I have already taken the steps I read in your post. The oil did not separate. I definitely have gas in my oil. I am also wondering if the electric fuel pump should run continuously or if it should pump up and stop with the key in the on position?<br>
<br>
I would truly be grateful for any input.<br>
<br>
Thank You,<br>

John Deere Gator water in the oil
Utility Vehicles UTV/ATV
Replies 20 Post by budzosmom

There lots of drain plugs on your tractor. Please be more specific as to what it is you want to drain.

//greg//

Agracat 2920 pto not working
Jinma Farmpro Agracat Nortrac
Replies 4 Post by greg_g

thanks

Cub Cadet 7274 Tractor oil filter cross reference
Cub Cadet
Replies 5 Post by TxJoey

Building permits and building codes can vary greatly. You need to check with your county on that. Probably a phone call to the building department can answer those questions or get you close. Do note if this is a true farm some areas have different regulations on them or if a true commercial operation again different regulations on those. I would suggest you make a information gathering phone call to begin with sharing as little info as you can. Here calling the building a "shop" compared to "barn" makes major differences in plans cost, building options and so forth.

As to the building itself would suggest you try and find building like you want and begin with asking that owner. Strongly suggest you do a lot of looking at buildings for there are many options and there can be wide variance in cost on similar buildings.

Pole Barn advice and help before building
Barns Pole Barns
Replies 4 Post by kthompson

I understand the fear of large repair bill. In my case I spent more on parts that were suppose to be the problem than it would have cost for dealer with wiring diagram and their knowledge would have cost. Also know each shop and case is different.

If still paying off, have you checked how long warranty is?

Boomer 8N not moving again
New Holland Tractors
Replies 6 Post by kthompson

This has been topic before and with all such issues the best is to avoid it. Am sure that is why the thought of the chain.

Slow rpms to give time to react helps a lot and also often raising the auger to clear it can. However the stuck auger will still happen so be careful.

Use pry bar or such to rotate the auger back with tractor turn off.

Know there was talk in another thread about using hyd powered auger for this reason so you can reverse it out. kt

Kubota B2620 3pt hitch won t lift
Kubota Tractors
Replies 8 Post by kthompson

Both front and rear differentials have drain plugs. But that's not all. You also need to drain the transmission and the transfer case. They share gear oil with the rear differential housing.

//greg//

2003 agricat 254
Jinma Farmpro Agracat Nortrac
Replies 4 Post by greg_g

I noticed that the rear end was leaking on my x500 and also noticed it was low on hyd.fluid can you fill it yourself or do you need to take it to the dealer? if you can fill it yourself will tractor hyd. fluid work.

leaking rear end on x500
Garden Tractors
Replies 1 Post by fireman14

May 17th I had the local mechanic who works on my L3240 come out to the house and do the 200 hour service on my tractor. The hour meter was at 203 hours. It took him about two hours to do all that was a part of my manuals requirements for the 200 hour check up. All was well except for some bolts that needed to be torqued to the correct tightness. It has been an amazing two years with the L3240.

New Kubota L3240 First Look Review
Kubota Tractors
Replies 87 Post by Sassi7855

I have an early 80's Belarus 820 that my father bought new. We never had any issue with the hydraulics before but today the 3 point hitch arms will not raise or lower. The reservoir is full. My nephew was going to use the tractor earlier and had move multiple levers. I believe everything is back to normal but the arms still won't move? Any help would be greatly appreciated?

belarus 820 3 point hitch arms wont raise
Belarus
Replies 2 Post by outdooryoung

[QUOTE=utcummins;154670] I am new to this forum and in need of some advice.I have a Mitsubishi D2000, the PTO is stuck in the up position and makes this aweful noise.I would not describe the noise as grinding, but its rather loud.Anyway after a day or 2 of siting it will lower itself and once I start it it raises in the up position and will not lower.Does anyone know what might be the problem on this tractor?And if I need to add fluid, where is the plug to do so?Thanks [/QUOTE]

I had the same/similar problem with the 1300, turns out I had to remove the lift section, force out the piston and clean & hone the cylinder and piston, then clean out the valve module, I replaced the 2 o-rings too.

moisture had been getting in at the shifter, I remade a boot for that. the moisture was most of the problem, causing crud and rust in the cylinder that jammed it ....

Tractor PTO will not lower
Mitsubishi
Replies 7 Post by JDwannabe

Can I also send this manual to me?

Duerr hp 678 Chipper Manual
Operating and Attachments
Replies 33 Post by tssea94