Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Yes, it probably is the whole fuel injection pump assembly. The question Greg and I have is why are you replacing it. If you have a little bit of fuel coming from each of the injection lines as you rotate the engine, it indicates the pump is working.
You had a problem with fuel getting to the pump, if I remember. Given the fuel being bio fuel, which has a tendancy to remove "black stuff" from the fuel system and plug filters, that needs to be taken care of.
Next, given the fuel from the injection pump would indicate that you did have fuel from pump, so next to check would be injectors. that can be done by removing them, reinstalling on the injector lines, priming the pump and injectors, and rotating the engine with the starter to check for fuel coming from injectors. If the fuel coming from the injector is not in a fog or sprays off to one side the injector is not performing correctly and needs attention or replacing.

How do I get out the fuel pump on jinma 224
Jinma Farmpro Agracat Nortrac
Replies 11 Post by Cyrus55

Actually the tractor will start with a bad seat switch. It only affects the pto.

955 compact PTO will not engage
John Deere Tractors
Replies 5 Post by jdgreen

I think that you should try and visit a hardware store. They will be able to help you on how to repair your rake at home. They will also give you tips on how to use rakes well while you are gardening. ;)

Bent Landscape rake
Garden and Landscape
Replies 3 Post by helgajones

I am gonna go and check it out. Been looking for some tools to use on my garden. I have been planning to make some designs and some nice landscape on the front.

Rockaway Landscaping Tool
Garden and Landscape
Replies 2 Post by helgajones

I have a pond at home and it seriously needs some new designs. I hope that you will be able to scan that pond magazine issue. I would really like to see that in order to get some ideas and to be able to start designing. :)

Pond Design Article
Garden and Landscape
Replies 17 Post by helgajones

Moved to Jinma Chinese Tractor Forum

McConnell Marc 425
Jinma Farmpro Agracat Nortrac
Replies 7 Post by DennisCTB

If you have a loader and it works its not the pump.

Shibaura SD1643 Hydraulic pump 3PH no lift
Shibaura
Replies 4 Post by jethead69

i would really love the owners manual for this wood chipper i am having a dickens of a time adjusting it to run properly. thank you momarazi

Duerr hp 678 Chipper Manual
Operating and Attachments
Replies 33 Post by momarazi

Hi KT,

Thanks for the reply. I have a exterior wall masonry fireplace that is very tall and is not accessible from the the top. Have a stainless steel liner and a Jotul cast iron stove. The house is on a hill and gets blasted by high winds from the North in the winter making for downdraft issues mostly to start but rarely so severe to cause concern otherwise. I have a commercial chimney pole system and brush that I used before the heating season.

My first season with this stove I had a chimney fire that ran its course with no damage. But it is like watching a jet engine go out of control,the stainless has a very high heat tolerance, but who knows how long it can sustain it or desire to test it out.

Cutting,collecting and burning wood has long been a fascination for me. I was the kid who begged his grandfather when on vacation at the Jersey shore at a rental bungalow that happened to have a masonry fireplace; please please Papa can we have a fire? What a loving man he was to set a blazing wood fire for me with 95 degrees and no AC. He loved his grandsons, the boys...

We have been burning some of my wood supply in outdoor campfires but it will take 50 years to burn all of it that way. May have to see if anyone bites on Craigs list :-)

Log Splitter Injury
Shop Tools
Replies 30 Post by DennisCTB

So you found a head there?

Yanmar Tractor Diesel 3T72 Parts
Yanmar Tractors
Replies 7 Post by adayxs

I have an update now. I did more checking and when the tractor is running if I wiggle the connector going into the controller the glow plug light will come on and go off randomly. Also, if I turn the key to right to glow the plugs and wiggle the connecton I hear a click coming from the controller randomly. It seems that I may have a bad connection in the connector that snaps into the controller. Nothing looks bad in the individual connections. I did manage to get a few of the individual plugs to come out but I can't get them all out to squeeze tighter. I also wiggled the wires before connector and they seem fine.

I don't know for sure how to check the glow plugs. I did pull them out and set digital volt meter to ohms. I then place one end of volt meter on top of glow plug and other and other end on the electrode and I got no reading when set to ohms. Is this the correct way to check my glow plugs? It appears to be no resistance so I think they are burnt out? Can someone please give me some advice?

I asked the dealer where I purchased this tractor for help with this problem. This is where I buy all my filters, oil and parts and they were short and rude to me for asking for advice on trouble shooting my glow plug system?? I feel offended by their actions. I was good to the dealer and gave them plenty of business. I am willing to purchase the parts from the dealer if I can figure out what to buy. Seem if they can't collect a labor fee they don't want anything to do with me.

I sure hope to get some help here, thanks everyone!

Cub 7265 Glow Plug Lamp On During Operation
Cub Cadet
Replies 3 Post by GRIZZLYJO

I think the first one is draft control limit for the 3PH. There is also a tilt on the 3PH for one of the other ones.

what do switches do on n189 hinomoto
Hinomoto
Replies 3 Post by jobone

Trying to locate a Jinma Rhino 754 Tractor Service Manual for my late 1980's / early 1990's model. Any idea where I can find this manual for download or purchase?

Jinma 754
Jinma Farmpro Agracat Nortrac
Replies 6 Post by saglejeff

I'd use a universal hydraulic/transmission fluid like JD303

Shibaura SU-1540 Tractor Hydraulic fluid type
Shibaura
Replies 4 Post by lsheaffer

Update seven years later....

Almost gave up on the 026 again this year. Even bought a new saw at Lowes, but also bought a new plug for the 026 as a last ditch effort to get her going again.

New plug new gas, resurrected. Returned new saw to Lowes.

That was 4 weeks ago. Got another tree to work on today. Will see if the 026 is ready to go.

Dennis

Stihl 026 chain saw does not start
Shop Tools
Replies 24 Post by DennisCTB

5/14/2015 - <br>
<br>
After rebuilding 510 Long, injector, with new gaskets; I'm not getting pressure to injector, hydraulic damper leaking a small amount diesel fuel;<br>
Solution? or Suggestions. <br>
<br>

Long 510 Inector rebuilt with new gaskets now
Long
Replies 2 Post by skipsell

And double up on injector cleaning fuel additive as well. Good chance some of that crud has made its way to the injector tips as well.

//greg//

Jinma 224 having fuel injection problems
Jinma Farmpro Agracat Nortrac
Replies 3 Post by greg_g

My starter light is not coming on my Belarus Tractor. So the key will not work and the motor won't start.<br>
<br>
Where to start?

Belarus starter light does not come on
Belarus
Replies 1 Post by villagedrunk

Based upon limited experience it sounds like you have air being sucked into your hyd system. Only have had limited experience with this and the tractor it was on the fluid would foam up as run as the air was mixed in it but it had more hyd power upon start up compared to after running for the air I guess floated out of the oil.

Look for a sign of leak on the hyd system.

Air in hydraulic reservoir
John Deere Tractors
Replies 2 Post by kthompson

Just had the exact same issue as you are having. In fact I took my gator into the dealership and they said that my engine needs replaced. I had no issues with the gator before it was stored for the winter. Tried to start the gator in the early spring and battery was dead, replaced the battery. Still would not start. Changed spark plugs, nothing, cracked the fuel line and was getting fuel. Nothing wrong with the air intake. I order the ignition module from Gator Parts Store part #AM132577 John Deere Module is the description. It bolts on with 2 10mm bolts and plugs in to a wiring harness. The gator started right up. The JD mechanic said it cannot be the ignition module, "those never go bad and there is know way to test them, it's not the module". I am so glad I read an earlier post that said the mechanics would say that, he did! Any way, hope this helps.

01 Gator HXP 4x4 cranks will not start has fuel spark
Utility Vehicles UTV/ATV
Replies 14 Post by mrducks