Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Can I also send this manual to me?

Duerr hp 678 Chipper Manual
Operating and Attachments
Replies 33 Post by tssea94

What did you find out about your clutch problems, I have a mte2000d doing the same thing and I replace everything you did. I would like to know how you fixed it.

Mitsubishi MT1601D Tractor clutch doesn t engage
Mitsubishi
Replies 10 Post by Jnsmas

I have a New Holland 6640. The power steering works great and a spear on the back can lift a 1000 pound bale of hay. However, the remote won't even lift the door of my baler. any suggestions?

Hydraylics
New Holland Tractors
Replies 1 Post by surbel

So my fianc� and I are looking to build a pole barn for a house when we get some land.I herd we have to have permits to build one.What kind do we need and how much do they normally cost?I live in Missouri.whats the best way to build it and to make sure we stay cool and warm when needed?we would be building it ourselves.azny other tips and help would be appreciated.

Pole Barn advice and help before building
Barns Pole Barns
Replies 4 Post by cheychey10

Hope this link works. Just hit it looking for something else and they have the setup to use with single shank subsoiler like Joel was talking about.

Laying Electric Line with subsoiler
Operating and Attachments
Replies 19 Post by kthompson

Sorry for the problem(s) you are having. My suggestion might not please you but would suggest taking it to the NH dealership. At least talk with the shop manager on the problem for it may be something they can find and fix cheaper than the hunt is. Don't ask how I know, just say I know with another brand!

When that model hit here I thought it was going be very popular till a friend told me how much they wanted for it.

Boomer 8N not moving again
New Holland Tractors
Replies 6 Post by kthompson

Fram PH7317 might be it

Cub Cadet 7274 Tractor oil filter cross reference
Cub Cadet
Replies 5 Post by DennisCTB

Not always necessary, depends upon the weight of the implement relative to the capacity of the pump. Increased revs are only really necessary if/when raising an implement causes a noticeable decrease in engine revs or increase in pump noise.

//greg//

Proper Engine RPM When Using Lift
Operating and Attachments
Replies 2 Post by greg_g

Did you check for excess play in the balancer shaft bushings? Were they replaced at the time of rebuild? This seems more likely than piston slap with only 300 hours unless you had a four corner seize situation. Did the engine ever stall unexpectedly? Just curious, where did you get your engine rebuild parts? Were they JD original or another brand?

John Deere 4276T engine knoock
Parts and Repair
Replies 12 Post by jdgreen

I assume that you are getting fuel in the crankcase and overfilling it? When you bled the fuel lines, did you loosen the lines at the injection pump? If so, then you might have loosened the fitting that the line screws onto. The fitting under the fuel line that is threaded into the pump can come loose when you loosen the fuel lines. If that fitting is left loose, fuel bypasses the fitting internally and leaks into the crankcase. Usually you have a misfire on that cylinder also, depending on how loose it is. There is a copper washer under the fitting that seals the connection.

JD850 blowing fuel and oil out
Parts and Repair
Replies 2 Post by jdgreen

Dennis know it hurts but think on the good times and experience. You will realize he meant more than you probably realized then and be thankful for the lessons you learned from the good and bad times there.

We planted a holly tree with cement dog where we buried our Golden and I think of him every time I cut around it. We buried ole shoes and such with him as he loved to bury such. Most were ones he had buried and we dug up and saved for some reason. Sure do miss that ole boy. Knew it was safe to be outside for he was a great snake dog. Could sniff either kind out real well. kt

My Labrador started limping has osteo sarcoma cancer
Everything and Anything
Replies 10 Post by kthompson

It is either the hand pump below the steering wheel or steering cylinder that is leaking by. We have had an assortment of different reasons for the failures depending on the make although we have not seen any one reason for when they do go under and after correcting units have not had other steering issues.
I'd contact the dealer so you can get it documented in Kubota's system of the trouble and it should be covered under warrantee.

Kubota 9560 Tractor Steering problems
Kubota Tractors
Replies 2 Post by Art White

Mahindra has taken over the 7532 cub that I own.
If they have an equivalent 7205 model
youll be able to buy from them.

cub cadet 7205 need backhoe attachment
Cub Cadet
Replies 7 Post by corvettteguy

You don't needed a leak in order to have bubbles in a hydraulic system. It's commonly caused by cavitation.

If there is no one-way restrictor valve on the loader arm or bucket (curl) circuits then lowering the loader too quickly with a load on it the viscosity of the fluid versus the vacuum caused on the other side of the cylinder could cause air to be inhaled.

The one-way choke valve limits the speed of lowering or dumping the bucket to a point where the fluid can be taken up rather than cavitation.

Best of luck.

Restoring 1910 for my property
Tractor Projects
Replies 2 Post by Murf

I guess I'm definitely in the minority in this crowd!

I love blue cheese! As for fat or calories, the taste is so strong that you don't need anywhere near as much of it as you would with milder cheeses.

One of my favourites is boneless skinless chicken breast with a little pocket slit into it and then grilled. Yum!

Best of luck.

Who likes blue cheese Survey
Everything and Anything
Replies 9 Post by Murf

The 7205s backhoe from Cub Cadet was the model 457. These backhoes have a subframe that hooks onto a bracket on the front of the transmission case, approximately under your feet, and to the top link (with a special high strength top link.

Most of CCs big implements were actually made by Woods Equipment. They can probably make up one that exactly fits your tractor if you don't mind buying new.

Note that if you do not have a loader you will need front weights and it will not work as well as when you have the loader lifting the tractor off the ground in the front.

cub cadet 7205 Which backhoe will fit
Loaders Back Hoes
Replies 2 Post by chashm

Do you happen to still have your plans for your Miracle Truss Building? I recently purchased one that has never been erected and I'm trying to locate a set of plans.

MiracleTruss buildings
Barns Pole Barns
Replies 20 Post by JLSkin5

Hi I am looking for another bucket for my Bradco 8LD backhoe. I would prefer a 10" or smaller but would be interested in any. Thanks, Rob

8LD Bucket
Loaders Back Hoes
Replies 1 Post by rob9770

Answered my own questions. Had to use heavy hammer and block of wood. Took some pounding all around hub cover, then once crack appeared got small screw driver and opened it up the rest of way.

Cub Cadet 7265
Cub Cadet
Replies 3 Post by DANBPA

good

Cubcadet7265 hard to start
Cub Cadet
Replies 10 Post by TxJoey