Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

This is why I asked for some suggestions. Great advise ! ...Somehow I didn't think of that.
You guys are right on...... only thing is does anybody know or have any Spec's or know what the Valve Clearance is
on this 80's Shibaura 3cyl diesel ?
No.....I don't have a manual ....But maybe someone
on the form may have one. Thank you guys very much for your
input.....I will do the valve adjustment first.
Needed 80's Shibaura 3cyl diesel Valve Clearance ?????
Thx Mike

Shibaura SD1643 Smokes Valve Adjustment or Injectors
Shibaura
Replies 6 Post by mcartsetc

I have a SD1643 USES THE ( NAPA FILTER # 21521 )
It may be the same.......
Mike

Need Oil Filter for Shibaura SD1400A
Shibaura
Replies 7 Post by mcartsetc

That's great you found the filter...mine looks like a pain in the a** to take apart....so I am leaving it alone.
Did you find the electric connecters that go to the lift
arm system under the seat ? If you use a test light to see
if you have power on the down side connector while the lever is in the down position that could be the problem.
( But stay clear of that brush hog while working on that electrical ) I think there are some type of solenoids
at the lift arms connectors that activates the up & down position. It may be as simple as switch those connectors one to the other...because the up one is working it sounds like....I don't know if you have the same system as mine.
Let me know what you find.

thank you
Mike

Shibaura SD2843T Hydraulic Filter location
Shibaura
Replies 11 Post by mcartsetc

Don't use that to start it.
You could toast you motor real easy.
if you do be careful to keep the rpms low
and fully choke it ...then zero the choke out
very slowly.
thx
Good luck
Mike

Start Tractor with B-12 Chemtool Starting Fluid
Belarus
Replies 11 Post by mcartsetc

Loader 2030
Ford 1710
Thx
Mike

Shibaura SD1800 loader
Shibaura
Replies 6 Post by mcartsetc

Thank you Gary...for your reply.
I will give it my best shot and see if I can get r done.
Thx
Mike

changing a Shibaura Fuel filter
Shibaura
Replies 3 Post by mcartsetc

That looks like a good size tractor...Its got to be 25hp Or better.<br>
I found my model numbers on the side of the trany just inside the drivers step..If its a graymarket someone may have removed the plate. There are also numbers on the block just in front of the starter. I dont think you will find a manual in our langage but Schaff has parts books. <br>
<br>
But those don't help much either. Those 3pto are elect/Hyd on Shibarua's difficult to understand. electric solenoid and hydraulic lifting systems. If all else fails finding the model number ....go find a dealer or one for sale somewhere and look at them and compare or take pics...you'll finds something the same to give you a clue.<br>
<br>
Hope this helps<br>
<br>
Thank you <br>
Mike

Shibaura Stiger manual and model number
Shibaura
Replies 4 Post by mcartsetc

Is that easy to fix ?
Do you have the correct Orings in stock for it ?
Or any instructions on how and where the Orings are
located ?
This is a well worth fixing tractor. This Shibaura has ten
times the power as the Kubota I have.
Also Can you tell me something about my Kubota B8200.
The loader Hydraulics seems to slow to me. Question is,
do ya have to run these kubotas with the RPM'S kinda high to make the loader hydraulics to work faster ?
thx
Mike

Shibaura SD 2243 Hydraulic leak down
Shibaura
Replies 5 Post by mcartsetc

Thank you For your help. I dont think its any problem So I will just leave well enough alone. Tractor seems to work just fine. Just thought I would through it out there to see if someone knew what this plug was for..... You Guys are a great help....I really think its a condensation drain. So I will let it go at that......Thanks
Mike

Kubota drain plug
Kubota Tractors
Replies 9 Post by mcartsetc

I ran across a maybe strange problem while changing the hydraulic fluid. I found a drain plug in the far back behind the rear differntal...I unscrewed the plug and it was completely dry as a bone. I still changed the hydro fluid from the strainer hole and cleaned the strainer and it fixed the hydraulics...its much better.
But Im concerned about this drain plug in the back that had no fluid in it. It seems to me this rear chamber should have fluid in it.
Can anybody tell me what this rear plug goes to...or if its suppose to be dry ?? It just to the right and below the PTO drive shaft.
Thank you
Mike

KUBOTA B8200 SLOW HYDRAULICS
Kubota Tractors
Replies 8 Post by mcartsetc

A lot of good points. But based on its condition they seem like real hours. The Original Tires have about 1/half inch of nobbs on them still. That seems like a high price you said it was worth. I did buy it for $ 5000 But thank you for evaluating it for me.
Mike

86 kubota b8200
Kubota Tractors
Replies 5 Post by mcartsetc

Hours sound real ...I have a 25 year old kubota with only 35 hours a year.
Iv'e seen those old kubota's like that out here in Arizona go for around $ 1500-2000 with a gannon only.
Mike

old kubota
Kubota Tractors
Replies 8 Post by mcartsetc

You are correct its best at 50% that way it does not jump when it pecks at the top of the pedal. I hate those clutchs like that.
I have two tractors one like that and one at 50% out.
The 50% tractor is way better to control...
Mike

jd 5220 clutch peddle adjustment
Parts and Repair
Replies 3 Post by mcartsetc

It Should be up to the A mark on the dipstick Not over it at all. When its at the B mark on the dipstick its a quart low. That way you always have a quart give or take to play with for hill and such.. Manuals are difficult to understand sometimes and they don't completely explain it like your understanding it. Remember its been translated from japp. I always top off to the A on the dipstick. It just gives you that much more oil for your engine..
Hope this helps.
Mike

CRANKCASE OIL LEVEL
Parts and Repair
Replies 8 Post by mcartsetc

Hi :

I have one of those Shibraua tractors to....mine is the SD1643 Model 3 cyl diesel loader and gannon. I seem to have the same problem with my gannon settling down as well.
On my early 80's model there is a round nobb just below the seat, if you turn it to tight it may stop or slow the three points hitch from falling . Yours may be different, I don't know. If you got hyd fluid running out your fill plug it could be its a bit to full....do you have a dip stick near the dash or close to your shifter ? You are a lucky guy because you got one of the best rice burners the japs made. Mine is like a small bolldozer, built very heavy duty and more powerful then any other tractor of simular size. Well worth fixing. Also could be as simple as a hyd filter , Have you changed it before ? Anyhow let us know what you find.
I also live in Az
Have a Great Day !
Mike

Shibaura model SP1740
Shibaura
Replies 3 Post by mcartsetc

Hi:
Kthompson
I got the starter in and working. Fired up the shibarua, and it runs great. I appolagize for my langgage in the last massage but think I just get upset with myself as well for not knowing better about choosing the right people to fix things for me. Anyhow thank you again for your suggestion.
Mike

Starter not engaging flywheel
Shibaura
Replies 13 Post by mcartsetc

Hey;<br>
Guys<br>
I have a Shibarua SD1643 4X4 loader with ganon.<br>
Recently the starter seemed to just spin. and does not egage the flywheel. I pulled it off had it repaired I tested it before installing it, worked great outside the motor. But it still just spins when you turn the key.<br>
I have tryed lots of things to fix it but can't think of any more. Makes no scence same starter with rebuilt drive same gear, solinod works good to. the flywheel looks good and turn over just fine Good battery wired correctly.<br>
Please can someone make any suggestions. Thank you<br>

Shibarua SD1643 starter problem
Shibaura
Replies 1 Post by mcartsetc