Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Oneace, what brand is the after-mkt loader, and what is it being compared to?

Woods vs Kubota Loaders
Loaders Back Hoes
Replies 23 Post by dfkrug

I found this thread interesting and thought I'd throw this comment in to consider. All hazardous material (includes oil) sold in the USA must by law list the specs it meets listed by the FTC. I believe the "use our oil or else" went out the window by a court decision in Caterpillar vs Quaker State where the specs list was met by both oils and Caterpillar was ordered to do the warranty work. I think this was back in the early 70's.

Kubota Transmission Fluid SUDT
Kubota Tractors
Replies 57 Post by bluetay

I don't know what an Enzo is..... but I have a question:

Is there someplace to put a bag of groceries if there are two people on board?

60 quot MMM blues
Kubota Tractors
Replies 43 Post by DRankin

Sheesh...Wow...all that... I just read the whole thread and have a bit of a headache now. I shouldn't try to absorb all this heady stuff in one sitting.<br>
<br>
Bottom line for me, and what appears to be the majority (based in sales) of owners of the smaller frame CUTS is the convenience, comfort, and power still associated with the HST. If somebody were doing consistent or serious draft work, they wouldn't/shouldn't be buying a 4110 anyway. In addition, If I needed to put more power to the ground, I would NOT buy a 4110 gear to replace my 4110 HST. I would buy a 4210/4310 HST to replace my 4110 HST. Personally, I like having a free hand to wave at the pretty girls driving past my house on their way to the beach :~)

4110 Transmission
John Deere Tractors
Replies 44 Post by bigpete

Thanks for the advice, I've learn also in the past to sometimes take it!

MMM capabilities
New Holland Tractors
Replies 3 Post by rwacho

I have a question concerning my 638 loader on my CC 7265. What is the bolt for that is located on the valve assembly just to the bottom of the valve handle rod? It looks like an adjusting bolt with a lock nut. I looked in my owners manual for this loader and it doesn't mention a thing about this bolt. Can anybody tell me what this bolt is for and thanks.

638 Loader Question
Cub Cadet
Replies 1 Post by Grizzly J

I asked a Cub dealer for the part numbers for all of the filters my 7265 has. I then went to NAPA and they can't cross reference any of the part numbers. This means that Wix doesn't make a filter yet for this tractor or they haven't tried to see if what they have will fit. The NAPA dealer did say that if I brought in the air filter he is sure they will have something similar that will fit. At $81.00 for an air filter I think I will look into this! Darn, I can't believe that Mitsubishi is the only one to make filters for this tractor.

Filters for CC 7265
Cub Cadet
Replies 4 Post by Grizzly J

I have the woods 7500 with the pto pump
I have used it on 5 different tractors.
one of the big advantages is you can use it on any tractor
loan it to a friend or family member without loaning the tractor too, if they have a 30hp tractor or bigger.
or a subframe kit will allow use on a smaller tractor.
if you leave the backhoe unhooked for months at a time
you don't have to worry about the old fluid contaminating
you entire tractor. Ken

woods backhoe on a kubota 3130
Kubota Tractors
Replies 4 Post by Ken

I had much the same problem with clumps and also streaks where the tires run. My mower is a Kioti but after looking at a Caroni the only difference I saw was the paint. Well any way turns out the belt wasn't tight enough. I tightened it to specs but the dealer suggested setting it to 1/2 inch or 3/4inch deflection with moderate pressure (16 to 20 pounds spring pull) between the center and one outside pulley. Since doing that I've had no problem. I have a LK3054 Kioti and I run in fifth or sixth gear, in new grass I run in fifth and keep rpms at full throttle and I'm happy with the results. Oh, the mower is a 72 inch three blade type rear discharge.

unhappy with my mowing deck
Kubota Tractors
Replies 6 Post by bluetay

Just drove a CK30HST and the feel was very good. Good size feel, not too small but very good handling.

New CK25andCK30
Kioti Tractors
Replies 11 Post by cessnadriver

Well I went with the Woods 6' Standard Duty cutter. I used it for a couple of hours this afternoon and am very pleased with it. I compared the specs on it versus some other Medium duty cutters (Bush Hog Squeeler) & they were exactly the same....11 gague deck, 65 hp gearbox, slip clutch and stump jumper, ect. Got it for $1,175, same as the Bush Hog Brand.

Thanks for all your help. Now, if I could just get a tiller & box blade, I'll be all set. (& broke) :)

Best Mid Range Cutter
Mowers Field and Finish
Replies 15 Post by Tomahog

Sounds like a great deal. Is it 4WD? 4WD is almost mandatory for FEL use.

JD700 is the price right
John Deere Tractors
Replies 3 Post by kwschumm

You are comparing apples to oranges....the kit built
unit you are referring to for $3500 is self-propelled
and not an attachment. They are usually for those who
do not have tractors. You are comparing it to the "real"
backhoe ATTACHMENTS, which require a tractor. I built a similar CADDigger from plans and it was quite useful. I also have b/h attachments for my tractors. See "Kit-built Backhoe" thread on this site.

small backhoes
Loaders Back Hoes
Replies 14 Post by dfkrug

Well, lets see here, Age: 33; CI:23; DCI:17, GCI:6. Wow, that's downright pathedic!<br>
<br>
Sorry, I'll keep quiet till I can get this problem fixed!

What is your self-worth
Just For Fun Off Topic
Replies 34 Post by AV8R

You may be unfamiliar with hitch designations but there are catagory O the smallest, then O-1 then 1-2, 2-3,and 3-4 for the very largest of tractors. Unfortunately the market was caught off it's feet a little with the demand for O-1 with all the sub-compacts coming out and many people tried to sell the 1-2 cat implements for them and they did not work properly.

Which Model s Would You Recomend
Kubota Tractors
Replies 8 Post by Art White

I just got my new 790 today, was wondering where i could get more info. on shiming the hydraulic pump?

790 hydraulic pressure boosted
John Deere Tractors
Replies 42 Post by jusbauer37

It is a Kubota and of coarse it will pull a 12 or 14 inch bottom. I normally find a good tiller and deep ripper more worth while then a moldboard plow.

moldboard plow
Kubota Tractors
Replies 7 Post by Art White

many thanks

what you have is exactly what i need just to get things into place in my mind (i'm great with cars and mechanically ok, but totally new to tractors)

it wont let me put my email here so i'll change profile and email you

Newbie help for back hoe
Loaders Back Hoes
Replies 8 Post by ant549

Here is a link to the PDF file.

tc29 3 point hitch capacity
New Holland Tractors
Replies 5 Post by BillMullens

I HAVE HAD LUCK USING THE WIX FILTER WEBSITE (WIXFILTERS.COM) AND USING THE AKLLIS CHALMERS CROSS TO MY HINOMOTO C174.

Hinomoto C172 Oil Filter
Hinomoto
Replies 2 Post by ROBERT