Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

[QUOTE=bogman;197925] Pick the brains of Northerns tractor guy. you don't have to get it from him, but I bet he can tell you which one you need. on the engine there is a pl ... [/QUOTE]

ThaKS for the info!

Jinma 224 leaking hyd oil into engine oil
Jinma Farmpro Agracat Nortrac
Replies 6 Post by csxbill

SHIBAURA STIGER SD2243 MANUAL

HELP. I have looked for the hydraulic filter and can't find it. I know it is clogged but I can't find it to clean it. Can you tell me exactly where it is??? I also have a smaller Shibaura tractor that wouldn't lift the tiller and I took the filter out and cleaned it and put new fluid in it and it works good.

SHIBAURA STIGER SD2243 3PH Lift Problems
Shibaura
Replies 24 Post by ace0101

Thanks. These Turf Gators do not have the same trans as the others. They are based more on golf car tech. 13hp air-cooled Kawasaki engines with starter/generators activated by stepping on the gas pedal in forward or reverse. 4-wheel disc brakes, 4-wheel suspension. I have tried them on our toughest terrain and they climb just fine without locking diffs. A lot of our work involves starting and stopping and the way they are set up saves time and fiddling with other controls. The shifter between the seats is similar, but there does not seem to be any provision on the transmission for locking. They go just fast enough for us and they are nice to drive.

gator differential lock
Utility Vehicles UTV/ATV
Replies 3 Post by Trainpilot

i cant get the front bucket to raise more than 3 inches. it swivels fine but wont raise. any ideas?

ford 1720
New Holland Tractors
Replies 2 Post by landonw

[QUOTE=MHarryE;197908] I was going to add it should be a sight glass on the rear like the L3710 I once owned, difficult to see level because of fluid color, but its there. [/QUOTE]Thank you

Kubota Tranny dip stick location
Kubota Tractors
Replies 5 Post by flatom29

[QUOTE=Art White;197892] You half to remove the plunger to check for the failed part.When you remove the bottom cover be careful that you don't loose any parts.Has the detent been working for float? [/QUOTE]Do you know where dip stick is Located on L3010 HST its not on floor like others they show on utube

leak in loader control box
Kubota Tractors
Replies 8 Post by flatom29

Economical. The cost of concrete floors is very low, about $2 to $6 per square foot to polish a plain gray slab, giving it a lustrous sheen. The concrete's tonal differences, subtle cracks and aggregates take on a stonelike, natural feel. More elaborate finishes cost around $5 to $8 per square foot

stone vs concrete floors
Barns Pole Barns
Replies 6 Post by Christopher1

One of the top power tool manufacturers is Eastman Shop. They supply tools and power tools to over 40 countries around the world. The awards they won include Engineering Export Award, National Export Award, and EEPC National Award. The range of power tools included Angle Cutter, Marble and Stone Cutter, Angle Grinder, Electric Drill and Screwdriver, and Electric Drill. Their hand tools include Pliers - mini pliers, circlip pliers, side cutting, long nose, Hammers - cross pein, plastic mallet, claw, Spanners and Wrenches, and more. The countries include those in Africa and Middle East, Asia, Europe, Central America, Russia, and South America. You have automotive tools, repair tools, tools for construction work and gardening work.

North American Power Tools
Shop Tools
Replies 12 Post by Christopher1

How did you bleed it?

IH 254 Won t start
Other Tractor Brands
Replies 4 Post by lsheaffer

I have a Nalahay 254 (Tiashan) with the 295T diesel engine by Shandong Tractor works that I have had for 21 years. My guess is it was maybe 10 years old when I got it. My brakes are gone and I need to replace them. Can anyone tell me who to contact to try to get the parts and maybe directions on how to do the job? The tractor just keeps on running but if I can not fix the brakes I think its days will be numbered. Any help, advice, or direction will be appreciated. Thank you, David

Nalahay 254 brakes
Other Tractor Brands
Replies 1 Post by wdc1369

Only my second time trying the JD 990 inherited recently. The left brake is depressed (but not the right) and the parking brake will not disengage. The instruction manual says I need to fully depress the brakes, but it still doesn't work.<br>
Help

JD 990 parking brake will not disengage
John Deere Tractors
Replies 3 Post by BrentsWife

I Have a Kubota L3010 4x4 Tractor with Loader-The Loader control box is leaking fluid whenever I am using it-I took it apart and seen the left piston Leaking fluid-I see there is a cover held by 2 allan wrench screws is there a seal under them that I should replace or would it be something Else Thank you

leak in loader control box
Kubota Tractors
Replies 1 Post by flatom29

I Have a Kubota L3010 4x4 Tractor with Loader-The Loader control box is leaking fluid whenever I am using it-I took it apart and seen the left piston Leaking fluid-I see there is a cover held by 2 allan wrench screws is there a seal under them that I should replace or would it be something Else Thank you

leak in loader control box
Kubota Tractors
Replies 1 Post by flatom29

I Have a Kubota L3010 4x4 Tractor with Loader-The Loader control box is leaking fluid whenever I am using it-I took it apart and seen the left piston Leaking fluid-I see there is a cover held by 2 allan wrench screws is there a seal under them that I should replace or would it be something Else Thank you

leak in loader control box
Kubota Tractors
Replies 1 Post by flatom29

Here is the service manual for 360, 460, 510
I use it for my Long 2510.
I will probably have all of the information you need to look at this.
The tractors are very similar.

Long 2460 hydraulic problem
Long
Replies 4 Post by arcwelder

there is a valve on top of the valve chest on some early long tractors. this might need a 24mm ring spanner to open it. Underneath is a small coil spring which locates in the valve which could be stuck. If you have a 3/16 or maybe 5/16 screw you can screw it in to the valve even though it is not threaded.you should be able to pull the valve out using the screw.The screw size may not be correct or your set up may be different.

long 3 point linkage there is a vave on top of the valve chest on some
Long
Replies 1 Post by jawabike

[QUOTE=oldthreetime;197858] Somewhere my life got super-complicated and when I got back to refurbishing the interior control linkage of the 3-pt. hitch hydraulics of my Ford 800 ... [/QUOTE]

[l]yesterdaystractors.com[/l]

If they don’t have it you probably won’t find it anywhere else except maybe a tractor bone yard.

Best of luck.

Where to find parts for Ford 800 hydraulic cover
Antique Tractors
Replies 2 Post by Murf

i couldnt agree more with you. its all about money and profits today.everything is built cheap today compared to yesteryears products. i have long said john deere built its reputation on the 2 cylinder machines and still are making profits based on reputation and simplicity of machines built 50+ years ago

JD 4400 HST GEAR SELECTOR LEVER WILL NOT MOVE
John Deere Tractors
Replies 5 Post by TERRYG

You might want to download the tech manual to see the wiring schematic and troubleshooting guidance. I think your machine is covered by TM1518.

2003 4x2 gator lift bed
Utility Vehicles UTV/ATV
Replies 10 Post by JLMiller

DanC911 has posted a new photo.

Subject: 1976 Cub Cadet 1450.

Description: <br>It took me a few years to convince my dad to let me take this and get it running again. I love this little workhorse.

1976 Cub Cadet 1450 - New Pix by DanC911
Photos
Replies 1 Post by DanC911