Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Hi and welcome to the forum. Is this tractor new to you? do you have any manuals for it? If you unfamiliar with this tractor it could be several things. first you will want to make sure it is ether in high or low range. second you will want to have it ether in forward or reverse. ether of these could cause it not to move even though you have it in gear. if after you are sure of this and it still does not move, engage the differential lock and see if it moves. if to only moves in lock then you could have a broken axle, if it still does not move then it could be with the clutch.

here are manuals for a 250as, same with the exception of 4 wheel drive.

https://www.mediafire.com/?9nutl8b1f6m4jy9 Belarus T25A Repair Manual.pdf - 467 mb

http://www.mediafire.com/?9fylzh952p0ih8u Belarus T25A OM.pdf - 192 mb

https://www.mediafire.com/?8qlp9b2ebp1nxz6 Belarus 250A parts manual.rar - 110.2 Mb

Belarus 310 does not shift gears
Belarus
Replies 5 Post by cowrider

I would make sure you getting spark and that you are getting gas assuming this is a gasoline engine.

Pull plug and ground and see if you are getting spark.

If you have spark then pour a thimble of fuel into spark plug hole and replace plug and see if it fires. If no spark could be coil, points condenser.

If it does fire you know you have a fuel problem. I would look at fuel pump and replace fuel lines as possible causes.

You would have a hard time selling anything that does not run so it is worth figuring out your issue.

Bolens 1669 Does Not Start
Garden Tractors
Replies 6 Post by greyhorse

Forgive my forgetting how to post picture. I used angle iron for ease in getting right width and welding the two pieces together. <br>
<br>
I will leave bolts to the guard lose to allow the pump to wiggle with the shaft. Realize no hoses but it is easy to slip off and on. Even with not bolting it will not rotate but might want to walk off the shaft. <br>
<br>
Thanks for each suggestion.

PTO shaft mounted pump
Tractor Projects
Replies 16 Post by kthompson

[QUOTE=gatoraider;196157] The rod you speak of is only for the gas motors. The diesels have a mount on the driver's side that is supposed to address the forward/rear motion. Adjusting it is detailed in the shop manual, but I don't know how much it helps. Diesel motors shake so bad normally that they can't be tied down solid like the gas motors. [/QUOTE]

OK I found the mount you mentioned but cannot find anywhere how to check belt tightness for adjustment? Can you please point me in the right direction? The mount looks like it could be shimmed to limit motion some.

My main concern is that the belt seems to loose, it is actually rubbing on the outside of the belt against the gator frame on the bottom and is very close to hitting the exhaust manifold on the top. The writing on the outside of the belt is being rubbed off.

2000 6x4 gator Spreader bar between engine and tranny
Utility Vehicles UTV/ATV
Replies 4 Post by pposey

no spares for these models as hinomoto stopped making spares a long time ago

Hinomoto MB-1100D
Hinomoto
Replies 2 Post by gozoish951

do you wish to sell this hand tractor?

Hinomoto H65 - New Pix by blackstump
Photos
Replies 2 Post by gozoish951

did you buy the hinomoto? do you wish to sell it?

thank you

david

Hinomoto MB-1500 manual or any info
Hinomoto
Replies 5 Post by gozoish951

I am looking for information on backhoe for installation on Kubota L2800 tractor. I want one that is easy to mount and dismount as I will still want to use my 3-point hitch and PTO.

Backhoe for L2800
Kubota Tractors
Replies 3 Post by dtk1952

Can anyone recommend a backhoe attachment for a B2150 tractor?<br>
<br>
<br>

B2150 Backhoe attachment
Kubota Tractors
Replies 4 Post by jimvicknair

Nice manual. Any chance you have one for the 425a? I am buying my neighbors and the budget is tight to buy the manuals and want to spend money on filters and such.

Belarus 520 Tractor Leaking from bellhousing
Belarus
Replies 5 Post by m5040dt

Thanks , that was my next move, with every thing rebuild up to the steering wheel unit. I have the dash off and in the process of cleaning all the grease and trash off of the unit. I'll break the lines loose and if it doesn't turn ,i'll take it off and have it repaired

MF 231 power steering
Massey Ferguson Tractors
Replies 5 Post by bill1941

Sounds to me like your fuel tank vent is plugged. After some time it builds up a vacuum and cant move any more fuel. When this happens, remove your fuel cap, if you hear a swoosh sound, clean the vent.

belarus 400 shuts down after running
Belarus
Replies 5 Post by m5040dt

Thanks for bringing this up... seems like there are lots of grades / types...<br>
<br>
[i]<br>
-Nitrile (Buna-N)<br>
<br>
Temperature range: Between -65 degrees Fahrenheit and 300 degrees Fahrenheit.<br>
Suited for: General purpose seals, such as petroleum oils, water and some hydraulic fluids. Buna-N is also resistant against tears and abrasive treatment.<br>
Deficiencies: Buna-N can have problems with automotive brake fluid, ketones, phosphate ester hydraulic fluids, and nitro and halogenated hydrocarbons. While it is ozone and weather resistant, this resistance is not infallible but can be supported through compounding.<br>
Applications: Nitrile functions well in applications that have limited temperature and resistance requirements.<br>
<br>
-Ethylene Propylene Rubber (EPR)<br>
<br>
Temperature range: Between -65 degrees Fahrenheit and 300 degrees Fahrenheit.<br>
Suited for: Skydrol, a hydraulic fluid, has a noxious smell and can irritate skin, and its corrosive properties can be damaging to equipment. EPR o-rings work well with Skydrol and other hydraulic fluids, as well as steam, water, silicone oils, brake fluids and alcohols.<br>
Deficiencies: Similar to nitrile, EPR is not perfect for a wide-range of applications due to wear and tear issues.<br>
Applications: The aerospace industry uses EPR o-rings in hydraulic pumps.<br>
<br>
-Fluorocarbon (Viton)<br>
<br>
Suited for: Fluorocarbon is an all around material that can handle a number of applications, especially diverse sealing jobs that involve movement. It is also suited for petroleum oils, silicone fluids and gases, acids and some halogenated hydrocarbons, like carbon tetrachloride.<br>
Deficiencies: Fluorocarbon is not recommended for Skydrol, amines, esters and ethers with low molecular weight and hot hydrofluoric acids.<br>
Applications: Fluorocarbon o-rings are very versatile, and features in many different automotive, appliance and chemical processing industries.<br>
<br>
-Neoprene<br>
<br>
Suited for: Neoprene can seal refrigerants in refrigeration and air conditioner units, as well as petroleum oils and mild acid resistance silicate ester lubricants.<br>
Deficiencies: Finished neoprene products are often compounded with lead-based agents, which can be hazardous to human health. Additionally, some people are allergic to basic neoprene. In a functional sense, it is not very resistant to petroleum lubricants and oxygen.<br>
Applications: Neoprene functions well in refrigeration units of air conditioning systems.<br>
Temperature range: Between -65 degrees Fahrenheit and 300 degrees Fahrenheit. <br>
<br>
-Polyurethane<br>
<br>
Temperature range: Between -65 degrees Fahrenheit and 212 degrees Fahrenheit.<br>
Suited for: Polyurethane features abrasion and extrusion resistance, as well as general toughness.<br>
Deficiencies: Applications requiring good compression and heat resistance would not be suitable for polyurethane.<br>
Applications: Polyurethane o-rings are often used for hydraulic fittings, cylinders and valves, pneumatic tools, and firearms.<br>
<br>
-Silicone<br>
<br>
Temperature range: Between -120 degrees Fahrenheit and 450 degrees Fahrenheit, although silicone o-rings have been shown to withstand -175 degrees Fahrenheit during short periods of exposure.<br>
Deficiencies: Silicone exhibits poor tear resistance, abrasion and tensile strength. Their poor abrasion resistance means they are better suited for static applications than dynamic. They do perform well with water, steam or petroleum fluids, either.<br>
Applications: High temperature fuel injection ports can use silicone o-rings.<br>
Temperature range: Between -100 degrees Fahrenheit and 500 degrees Fahrenheit.<br>
Suited for: Pure PTFE o-rings are very rigid and hard to apply, but PTFE encapsulated o-rings handle surface wear well, in addition to exhibiting corrosion and abrasion resistance, non-permeability, chemical inertness and low absorption.<br>
Deficiencies: Like silicone, PTFE is rigid and is better suited to static applications.<br>
Applications: Examples of PTFE o-ring use includes automotive steering devices and paint guns.[/i]

Best o-rings for hydraulic quick connects
Loaders Back Hoes
Replies 2 Post by minimac

Thank you, I'll check it out

Komatsu WB140-2N water temperature gauge
Other Tractor Brands
Replies 3 Post by Emyres

Thanks! I don't see it either. I'll try to call tomorrow. Thanks again.

Karl

Roof VP75 lawnmowerbrush cutter
Garden Tractors
Replies 5 Post by karlthev

FWIW - I researched the specs on the hydraulic fluid for 6284 Cub very thoroughly. I found that Mystic JT5 hydraulic fluid had exactly the same specs as the Cub fluid and cost substantially less.

Cub Cadet 5254 4Wd Driveline Clunking Noise
Cub Cadet
Replies 12 Post by boltboss

Oil & charging

1500D Dash lights
Yanmar Tractors
Replies 2 Post by lsheaffer

Thanks for your advice, turns out that whoever made that batch of lift pumps for AGCO all had problems. I assume that holes formed in the rubber bladder and they would stop pumping fuel. I went through three lift pumps before the dealer got a new batch and the first one worked just fine/

Tractor was running and will not restart
Massey Ferguson Tractors
Replies 5 Post by poapony

Ok. thanks I will check them.

Starter sometimes clicks but won t start AMT600
Utility Vehicles UTV/ATV
Replies 20 Post by noglu10

Recieved Duerr 678. Came from small engine scrap heap, dead enging but fairly good frame. I need a parts breakdown and/or service manual so I can open this unit up and evaluate its worthyness.
If it is worth buying a Honda engine and refurbing rest of machine i will do so., or it will become parts .
Where can I get manuals in PDF format ?
Im new to this site so Ill learn as I go

Duerr hp 678 Chipper Manual
Operating and Attachments
Replies 33 Post by Tntrader