Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

I have a long 460 tractor. The hydraulics for the 3 point gets it hydraulic fluid from the rear axle housing which gets it fluid from the transmission. Same reservoir. If you look under the tractor rear axle housing you should see a separate drain plug. If you look to see where the hydraulic fluid line connects to it is under the rear axle housing. I was having the same problem. I drained the transmission housing and refilled with new fluid, cleaned the filter, etc. The hydraulics still did not work. When I disconnected the lower hydraulic line on the pump no fluid came out. No fluid was flowing to the pump. When I drained the rear axle housing transmission fluid water, hydraulic oil and clumps of goo drained out. Rinsed it out with an approved cleaner and put new fluid in the rear axle housing. The line from the axle housing to the screen filter could be plugged up also. You might need to remove the line and check for blockage.(The line that connects underneath the rear axle housing to the screen filter). Hope this helps you with your problem.<br>
I changed hydraulic fluid,(on full mark), cleaned filter, cleaned check valve piston, installed new hydraulic pump, bled air from system, checked sensitivity control, checked draft control. Not getting any fluid to check valve piston.<br>
Hydraulic 3 point hitch still does not work.<br>

Long 460 hydraulic problem
Long
Replies 10 Post by chevybig10

Sitting at home here in Cando, North Dakota and waiting for a major blizzard to hit our area on Christmas Day. Hoping Santa has auto-pilot, because it isn't going to be pretty.

Merry Christmas to everyone at TractorPoint. Happy New Year to all of you.

Joel

Happy Holidays
Everything and Anything
Replies 4 Post by candoarms

Right off the Bat the Low Price for MY 35 HP Nortrac was a big selling point. I did spring for the Extended warranty it parts only. The I had to get over the fact that this is a Parts Only Warranty. That it in a nut shell the first few week where they will send someone to work on it, Just is not true it isw not going to happen. That being said you better be willing to handle parts replacement on your own. If you can and for me its not a big deal. Just a annoyance. Clutch adjustments are a pain but I have had to do them on both mt Ford 800 an my Yanmar.

Most of the parts issues were pins falling off of linkages. PTO and 4WD selector. They will send the pins fast but some retainers(IE Self Made pins hold better.

For now I have had it 16 months it Has done what I asked it to do. Shuttle Shift? Power Steering on my 35XT and a Loader.

Worth it even being my own mechanic for right Now I say yes.

Quality Control Missed on NorTrac 35HP Tractor
Jinma Farmpro Agracat Nortrac
Replies 3 Post by Gameman

Hi:
Thank you for your reply. I have tried Google and got no hits for my tractor. Got any other suggestions?
Mike

Kioti LK3504 Front wheel drive problem
Kioti Tractors
Replies 3 Post by 19mosie38

Early on the Kubota's were not a quick attach like the new JD;s loader so we often went to after-market to gain that feature. To not have a Quick attach is asking for high labor bills when the tractors hit 10 years old when they need to be split.
I'd doubt that any of the loaders used today would be a bolt-on although many of the universals might have the right brackets available if you could find a comparable new loader the brackets are not that hard to fabricate.

Kubota B6200HST Compatible Loader
Loaders Back Hoes
Replies 3 Post by Art White

Could mount a couple rear view mirrors so your neck don't cramp up

Best Snowblower for Yanmar Compact Tractor
Yanmar Tractors
Replies 8 Post by dualhvision

Thanks so much. I appreciate the insight. I will be getting the actual hours of service and some pictures this week from my dad and will add that information to the post next week in hopes of narrowing the price down for him.

Thanks again.

Kubota 7200 - market value
Kubota Tractors
Replies 8 Post by vpaf2010

I have a 2005 790 that I want to put a heater on. Do I need the JD OEM adapter kit to go with it? I'm not even sure what it's for, but a few other forums I have seen have mentioned it.

790 Block Heater
John Deere Tractors
Replies 4 Post by Damrockfarm

After replacing the electric fuel pump I found the pick up line screen collapsed and kinked. Replaced it and now the pump won't prim the line. I have actually fed gas into the line to the pump and all it does is push it back to tank like it is pumping in reverse.<br>
Lost in Ohio over this debacle. It started after I shut it off one morning and tried restarting it. I heard a slight pop and the battery was dead. Figuring it was the battery cell which was 7 years old I replaced it. Here are the list of parts I have already replaced. Electric fuel pump. pick up line, fuel filter and battery.<br>
Thanks in advance for any help.

Trouble shooting no fuel in lines 620I XUV after replacing elc pump
Utility Vehicles UTV/ATV
Replies 2 Post by gettxman

Hydraulic excavator is the best digging tool, which are used to excavate materials above or below the bearing surface of the machine. It has become one of the main construction machineries in engineering construction. Daily maintenance is an effective way to extend its service life. Daily inspection is very important to ensure the digger to work durably and efficiently. For the self-employed, the daily inspection helps reduce maintenance costs. Here are some guidelines about the digger daily maintenance that may improve your digger�s working efficiency.<br>
<br>
Firstly, the operators should walk around the digger twice to check if there is something wrong with the chassis, and check if there is fuel oil leaking from the slewing bearing, and then the brake deceleration device and track bolt fastener. For a wheel hydraulic excavator, the operator also needs to check whether there is something wrong with the tires and its pressure.<br>
<br>
Secondly, you need to check whether the excavator bucket teeth are abraded, which will greatly increase resistance in the process of construction and reduce the working efficiency.<br>
<br>
Thirdly, it is an important issue to choose the right diesel oil. The type of the diesel should be chosen according to the ambient temperature. The diesel should not mix with impurities, dust and water, otherwise, it will cause wear to the fuel pump and damage the engine of the hydraulic excavator. Open the oil drain valve to draw off the water before daily operation and fill the fuel tank after the inspection. The air in the pipeline should be removed after the fuel in the engine is used up.<br>
<br>

Excavator Daily Maintenance Guidelines
John Deere Tractors
Replies 3 Post by optionals

Hello,
New to this site, May I ask if I can also recieve a e-mail for the Duerr 8 hp 678 Manual. My neighbor just give me his father-in-laws machine and for a winter project I want to rebuild/restore it next sping.

Thanks everyone,

KhunJeff

Duerr hp 678 Chipper Manual
Operating and Attachments
Replies 33 Post by KhunJeff

I have a d1600 with only 200 hours on and everything was perfect on the machine until a limb broke the front grill. I do not seem to be able to find the part anywhere. Can anyone help???

d1600 grill
Mitsubishi
Replies 5 Post by skippybob

Well I'm new here and just bought a Belarus 562. Does anyone know why my steering is locked? If you take the hydraulic line off the steering cylinder the steering wheel will turn.

562 steering locked
Belarus
Replies 1 Post by Cwmarsh

You could start by checking hydraulic oil level. Clean the hydraulic oil filter. Then check system pressure by hooking a gauge to the output.

825 Belarus three point hitch INOP
Belarus
Replies 4 Post by morant

My tractor is smoking light blue smoke when running and popping back through the muffler every once in a while. Oil appears at the base of the muffler. I adjusted the valves by the book and it got better but still doing this.

Belarus 800 series
Parts and Repair
Replies 3 Post by morant

Email me at parts at sheaftractor.net. I should be able to get you the parts you need.

Toyosha cs86 hinomoto c144 Massey Ferguson 1010
Massey Ferguson Tractors
Replies 3 Post by lsheaffer

Try here:
http://www.southern-global.com/engine-parts/pistons-rings

Toyosha cs86 hinomoto c144 Massey Ferguson 1010
Hinomoto
Replies 2 Post by mironb

Ended up taking the tractor to the dealer, the more I bled the system the longer it took and the shorter it would run.

As usual with my luck the lift pump I bought and installed on the tractor was bad. Took the tractor in Monday and they asked if I was using it and I told them yes as I needed it to feed round bales of hay. Dealer said they would get to it asap but they were pretty backed up. Got a Call around Tuesday lunch and said my Tractor was fixed, thrilled beyond belief. I asked what ended up being wrong thinking I had missed something very obvious, that is when they me the lift pump I purchased two weeks ago was bad.

MF 261 ill not restart
Massey Ferguson Tractors
Replies 3 Post by poapony

Are the Hydraulic hoses connected on the control on correctly?

Hydraulic Gremlins
Loaders Back Hoes
Replies 2 Post by minimac

Thanks for the quick reply! I will check out the Yahoo site you have noted. The hydraulic fluid currently on this tractor is AW32, but I am not sure if this is adequate for the power steering; as far as I can tell, the steering and general hydraulics work off the same pump. The previous owner did change the pump which I believe failed due to the 32 oil in warm weather i.e. not heavy enough. I am into cold weather now so the 32 may be ok but I just want to determine what the original spec was for the system. Thanks again and I will go to the Yahoo site.

Lubricants
Belarus
Replies 3 Post by p15cwbm