Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

I would use Kubota Super UDT Hydraulic fluid, I would not recommend any additives.

Kubota B2710 New to meadvice
Kubota Tractors
Replies 11 Post by DennisCTB

It would seem if a different coil was needed the instructions would have given the specs on it. Have you looked carefully to be sure it does not call for a totally different coil?

I recently was surprised an electrical valve did not have instruction on wiring and finally set down and read the full manual. It was after the English and Spanish instructions they showed the wiring instructions since there were drawings with no real words.

coil problem
Massey Ferguson Tractors
Replies 2 Post by kthompson

The best advice I can give you is to ask others locally how the poles hold up. Here we have high water levels and we see those poles used but not in buildings. For such that can easy be replaced or repaired. Then if rot on the part in the ground is the issue you may can cut it off and still have tall enough poles. kt

Utility poles or Presure treated posts
Barns Pole Barns
Replies 2 Post by kthompson

Got it; thanks a bunch. Now I know what I am dealing with, so we can go from there. I want to do that axle seal, so will probably tear into this at some point anyway. But first I will see what those rollers do for me. It's little hard to find neutral on this machine, in case that tells you anything about the input shaft or block. by the way, will I reuse hte spacers in the primary for then new rollers?

Input shaft spline or keyed
Utility Vehicles UTV/ATV
Replies 20 Post by Coachlarry

I have a Cub Cadet 7260 tractor that will not lift the 3 point hitch. In fact there is no pressure on the lifting arms. I can move them up and down easily. It is apparent that I am not getting fluid into the cylinder. My guess is the fluid is not making it through to the Hitch control valve. Do these valves break or freeze up? <br>
I have not used the tractor in about a year cause I have been restoring it but prior to that the hand control for the 3 pt was very hard to operate and could only get it to raise by applying a lot of pressure to it. It would make a squealing sound when it raised. While restoring the tractor I discovered the linkage to the hand control was froze up. I thought that was the problem. I fixed that but now the lift does not respond at all. I am thinking broken hitch control valve. What say you?

Hydro 3pt lift problem
Cub Cadet
Replies 1 Post by hayscreen

Howdy! I had the same trouble trying to hook up my hoses. I tried to relieve the pressure by pressing the implement male connector to the cement floor and even loosening the coupling with a wrench. Although I got a little.fluid out, the problem remained. What finally solved the problem was simply taking the offending male connector and striking it against the flat steel surface of the loader frame. I got a spurt of fluid and then I could connect with ease. You may want to wear some goggles to protect your eyes from the spray of hydraulic fluid. This whole problem could probably have been avoided if I had depressurized the system prior to removing the implement last fall by rocking the joystick in all directions a few times. Hope this helps.

Problem Connecting Hydraulic Hoses
Loaders Back Hoes
Replies 17 Post by rharryman

Fluid looks good? Let me add to that, since you change the fluid when it gets hot what does the fluid look like? Is it clear or by chance does it show water or air in it?

John Deere 2010 loss of hydraulics
John Deere Tractors
Replies 4 Post by kthompson

You're welcome.

e2303 4 trans dipstick
Hinomoto
Replies 5 Post by mironb

Hmm, okay I will start at the secondary. I wonder if spring pressure is too light causing the moveable sheave to open and up shift too soon. Not entirely sure I have that right.

1200A Bunker Rake Shudder under load
Utility Vehicles UTV/ATV
Replies 18 Post by Coachlarry

Have a piece scanned at a store that mixes paint.

Hinomoto E2004 paint code
Hinomoto
Replies 4 Post by lsheaffer

Just sent you an email.

Hinomoto E2602 Tractor converts to Massey Ferguson Tractor Model
Hinomoto
Replies 6 Post by lsheaffer

Hello, New here to this awesome site. I need some advice. My 3 point lever was getting more and more difficult to raise and lower. It would actually get stuctk in either position. Finally today it broke loose, sheared off from the the pin or bolt. It now is connected to nothing.<br>
My question. Is it possible to repair myself? It looks to be difficult to get too.<br>
What would have to be removed to repair? Any advice would be greatly appreciated.<br>
<br>
Thanks in advance

TZ24DA
New Holland Tractors
Replies 1 Post by TimsNH

Which lever engages the 4WD on a E2004? My decal/plate is worn off on the one I just bought. I got the 4WD to work, but I'm not sure which lever I engaged. Any info would help. Thanks

Hinomoto E2004 4X4 lever
Hinomoto
Replies 1 Post by Lowery

I don't have my manual handy and I am not sure about the meaning of the warning light figure on the right. There are four symbols.

Instrument panel
New Holland Tractors
Replies 1 Post by Croakerrpm

Jeff,

Great post on the Rockaway. I just picked one up myself after finding them online. Here's a picture of my rig. Bought it off www.idealrockaway.com

Rockaway Landscaping Rake
Garden and Landscape
Replies 9 Post by sclandscaper55

[QUOTE=Trainpilot;195069] That's great. I see you also have one of my favorite models of Vice Grips. [/QUOTE]

That's one my most used tools. Hard to believe it's not more popular. Thanks for your help TP.

1200A Secondary Cap Screw
Utility Vehicles UTV/ATV
Replies 16 Post by Coachlarry

If it makes this noise when sitting idling you may have a bad clutch throw out bearing. If it only does this when moving it sounds like you may have a different bearing going out.

If it only makes the noise when turning it could be worn spyder gears or wheel bearings. You could jack the rear up and with engine off and rotate the rear wheels by hand, a tough assignment, to see if you hear bearing noise.

My 2360 makes very little noise in that area when the tranny oil level is correct.

As you trouble shoot this let us know what you find.

I've talked to a lot of Long owners and they claim they are tough old tractors. //Ken

Long 2360 noisy transmission
Long
Replies 19 Post by krb1945

Thanks for the reply! It does'nt seem to be a slip clutch issue, it does it with a tiller attachment and also a post auger attachment both with different drive shafts, and both pieces of equipment work without any issues on my dads kubota. I will look into adjusting the pto clutch and see if that helps. I still just cant help but wonder if something like a shifting fork or a pin type something broke in the "PTO engage" system not allowing it to engage all the way or possibly be letting it try to disengage. Any other ides or suggestions are greatly appreciated and respected.Thanks!

Farmpro 2425 PTO slipping
Jinma Farmpro Agracat Nortrac
Replies 3 Post by Daves262

Make offers.

MT372 for sale in Illinois
Mitsubishi
Replies 2 Post by Chevy791979

Okay, I said melted, may be it didn't actually melt but the motion of the driveshaft / gearbox ground the shear bolt and it coated the gearbox shaft with the residue as the shaft was coming off the shaft. Which Loctite, blue?

Woods RC5 Bush Hog
Kioti Tractors
Replies 3 Post by 6x4gator