Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Thanks guys. Great information. I changed the filter in the last 15 hours with fluids but going to change the filter just in case. If that doesn't work Iam going to put a aftermarket mechanical pressure gauge and watch the pressure when bush hogging. Once again thanks for all the great advice. Will keep updated. Hopefully just a clogged oil filter.

393 Massey Ferguson dash light
Parts and Repair
Replies 12 Post by FlynnD

Is this a farm tractor, if so use a Jinnma 254 diagram on Johns trasctor site

Nortrac 254 wiring diagram
Jinma Farmpro Agracat Nortrac
Replies 3 Post by Scotiascott

What is exactly the same??? You need to describe exactly what is happening when it won't move. When it won't move do the clutches shift like they are supposed to. Will they shift in neutral? Does the belt slip? Does the front clutch try to close? If the back clutch is turning is the shaft that it's on turning with it? Is there any noise that is audible? Can you push it by hand?

John Deere AMT626 stops moving hot
Utility Vehicles UTV/ATV
Replies 5 Post by gatoraider

It does have Draft Control I have tried it both at the bottom and the top. I have another MF, and have used the Draft Control before. I keep it at the top, to get the other lever to raise and lower the arms. They will go up and down fine, accept when you put weight on them. I can even stand on the arms and mash them down. It is harder to mash them down with the engine at a higher RPM, but I can still mash them down. I thought If I could adjust the relief valve on the pump without pulling the pump maybe I could increase the pressure and that would help.

Massey 245 3 Pt Hyd Lift
Massey Ferguson Tractors
Replies 16 Post by mikemills

This fall a neigbor wants me to use the subsoiler to cut underground water drain offs. I agree with the uses but mostly sets in the barn.

What Rear Tractor Implement Do You Use Most Survey
Operating and Attachments
Replies 22 Post by yocsr1

I've got a Foton that works the same way. For general raise and lower I use both levers. Doesn't work like my Ford.

Kioti 3 Point hitch levers
Kioti Tractors
Replies 2 Post by yocsr1

I had my case locking up and would not move until I discovered the transmission switch located under the brake pedal was shorted. It seems silly for case to place that switch right under the brakes when all they had to do was to use the brake light switch. Now every time I brake it's much quicker and I only need one foot, not one on the switch and one on the brakes. Yes, I know about the other switch on the loader control lever.

Case 580 Transmission disconnect switch - a better way
Case
Replies 1 Post by Handiman

I ended up purchasing a cutting torch $240 and burned out the two sections. The other oils I ordered were not any good either, waste of money and time ordering the stuff. My new pin went in after I reduced its diameter .010" plus I added my own grease fitting. Shameful engineering from Case Mfr.

Lower stabilizer pin rusted in
Case
Replies 9 Post by Handiman

The tractor will shutter in that gear range whether loaded or not. Really need to be careful backing up to equipment to hook up. It does it less noticeablly in lower gears. It has four ranges from crawl low middle high with 1-4 gears. The shuttle lever will shift it from forward to reverse. Dealership and Kioti does not believe there is a problem. They say use a lower gear and let the clutch out completely. I asked if they have tried that procedure trying to ease back to hook up a mower or anything else.

Clutch issues
Kioti Tractors
Replies 12 Post by cwp003

It is a glide shift transmission. On advise of the dealer I changed the filters because of the shift problem. I lubed the shift lever, checked electrical connections and fuses. Do you know if the cluck linkage ever needs adjusting on this model?

L4330 GST won t shift into upper gears
Kubota Tractors
Replies 8 Post by zspitzer

I learned a long time back look for the little or simple things first. Seems we like to attack an issue the other way. Glad you got it taken care of.

Kioti Tractor How to test Battery vs Alternator Problem
Kioti Tractors
Replies 5 Post by kthompson

jrowley have you gotten it fixed?

Willie, you know that buried auger would have made a great anchor for a corner post. I wonder if anyone has made a pto auger with a reverse in the gear box? kt

B2620 implement arms won t move
Kubota Tractors
Replies 23 Post by kthompson

Don't know I can fully answer your questions but on my Kubota it has both draft and position. Years ago had experience with older Ford. But think the Kubota will be most like your Kioti. You use the position control to set the depth you want to use the plow at. Then you use the draft control to keep the plow at that setting as the ground raises and lowers. You use the position control to raise and lower the plow or blade or what ever.

My best suggestion for you is to put a plow on the tractor and get in a place to just try it at slow speed so you can feel and watch the action of the lift working as you plow. If your tractor has speed adjustment on the lift it can also affect the draft's operation.

Hope that helps.

Draft control
Kioti Tractors
Replies 2 Post by kthompson

Your tractor may also have a line on the Tachometer marked PTO. Which as Auerbach said is just a pinch under full throttle.<br>
<br>
Depending on what you are using the tractor for the temp guage not working could be a bigger concern. For example I mow with mine and the radiator screen tends to get clogged with debris, the gauge has saved me on a couple of occasions where I was not so attentive :(

Kioti 1914 temp gauge does not work
Kioti Tractors
Replies 4 Post by DennisCTB

All the wiring was found good, so I tested the rear pedal potentiometer and found it to read .7Vdc to 3.9. I was able to get it adjusted to a point to clear the fault code. Today when I went to use it, the problem came back, I reset it, and no issues during the 2 hours of use.
I was told that the potentiometer should be .6 to 4.7Vdc. Is this correct? I may need a new rear pedal potentiometer.

John Deere 2004 4210 Drive Problem
John Deere Tractors
Replies 7 Post by bbarnes42

jadezhang has posted a new photo.

Subject: 11 Chinese diesel engines .

Description: <br>Changchai, Xinchai, Xichai, Laidong, Yangdong, Jiangdong, YTO, Yunnei, Lijia, Xinxiang, Quanchai...

11 Chinese diesel engines - New Pix by jadezhang
Photos
Replies 1 Post by jadezhang

My Case tractor, same as an NH, has an electric fuel pump. With the ignition turned on, but without the engine running and when at a half tank or less you can hear the fuel dumping back into the fuel tank.

New Holland TC35 starving for fuel
New Holland Tractors
Replies 6 Post by bloggins

[QUOTE=gandalf;180423] Thanks guys; I talked to my dealer yesterday and was told that the pin inside the silinoid that pushes a ball bearing to let fluid by was bent.If all the ball bearing does is let fluid by then how would it bend. The pin is in a track/slot? and is powered by an electromagnet to push the bearing? So how does the pin bend? [/QUOTE]

Gandalf what wasthe part that was replaced im thinking i have the same problem and was hoping not to have to go to the dealer

DK35 4wd problem 2007
Kioti Tractors
Replies 18 Post by kirkdspain

Hello
Just wondering if the ecu fixed the problem??

New Holland 8260 Shuttle Problems
Tractor Projects
Replies 5 Post by beinlich1

I tried to turn the steering wheel and no dice. I think there may be a problem in the linkage as u suggest. may get under it tomorrow. THanks!

Long 510 Steering issues
Long
Replies 21 Post by marty5764