Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

First thought at the "noise between your legs" is throwout bearing. If you switch back to 2wd and the noise persists, that might be your problem. If the noise goes away, then you've likely narrowed the issue down to the transfer case.

//greg//

4wd problem
Jinma Farmpro Agracat Nortrac
Replies 7 Post by greg_g

I have a factory limited slip differential on the Tundra. I can drive just about anywhere on my land and off road in two wheel drive. <br>
<br>
I have driven similar trucks on the same land and they don't go anywhere without 4wd engaged.<br>
<br>

Differential Lockers and Limitied Slip Units
Pickup Trucks and Trailers
Replies 25 Post by DRankin

Ken,

Have you tried these guys?

Auto Manufacturer parts availability policies
Antique Tractors
Replies 23 Post by Chief

Peters, that link did not work for me but it looks like it should. Maybe a DNS glitch.

Thanks for the info guys. I'm planning to finish our basement and have some forced air ducts to run and would rather not have to soffit around them. I guess the right thing to do is read the manufacturer specs for our I-Joists.

Cutting holes in I-Joists
Home Improvement
Replies 9 Post by kwschumm

The only place that I have seen turf tires and Jimna tractors mentioned in the same sentence is Northern Tool. <br>
<br>
They do stock matched sets(front and rear)turfs, but as mentioned, not cheap.

wheels
Jinma Farmpro Agracat Nortrac
Replies 5 Post by DRankin

I think that would be the right way to use a middle buster/sub-soiler attachment, but a good way to break a really nice backhoe.

Trenching with the BX-23
Kubota Tractors
Replies 21 Post by DRankin

I was talking best (to have a concrete and floor jack). I have seen people use a floor jack on a dirt floor. I guess you could lay down a sheet of plywood or something. You don't really need to move back very far. Make sure the front half is blocked well.

JD 1070 Clutch Replacement
Parts and Repair
Replies 16 Post by Peters

If you are loading you transfer a lot of weight to the front end. You need a large weight box to compensate. All this does is add weight.

The 3 pt hitch under plowing or tilling load tranfers the weight to the front end. If they are driven you are always better off.

Mahindra tractor review
Other Tractor Brands
Replies 6 Post by Peters

The hydraulics run off a separate pump on the 955 so they are un affected by the HST. Only the time it boggs is when the you push the peddle.
Joe is right about the switch. It could just be a faulty switch or solenoid valve. If the valve is not opening fully it could also be restricting the fuel flow.
I guess you could check the switch by increasing the engine speed in neutral and moving on the seat.

BX23 Gasping
Kubota Tractors
Replies 9 Post by Peters

Not every meter is capable of reading the frequency. Mine doesnot either. The better meters are inductive, they just clip over the electrical wire.

Measuring Frequency in a generator
Shop Tools
Replies 26 Post by Peters

No specific Kubota experience here. But the fact that you're considering check chains sounds to me like you've got a leakdown problem. If I owned a B7800, I think I'd fix the hydraulics, rather than apply a steel bandaid

//greg//

Stabilizer drop limit chains for brush cutter
Mowers Field and Finish
Replies 3 Post by greg_g

I have seen welded on larger fitting, threaded and threaded and welded. If you look closely at the fitting you should be able to tell. At this point you may only be able to weld with out replacing the pipe?

quicke tilt cylinder
Loaders Back Hoes
Replies 2 Post by Peters

It is difficult to measure up O'rings after the are in oil as they expand slightly. Most rubbers will absorb the oil into the crosslinked polymer over time and swell.
It is also difficult to find a full set of metric O'rings. You are problably better to get the set from Kioti.

LB1914
Kioti Tractors
Replies 4 Post by Peters

I can see why you waited a couple of days to post this. I think technical term is pumpkin heads. At least that is the term we used in MA for the old senator with the big head.

Hey Randy I think I found our cap
Just For Fun Off Topic
Replies 9 Post by Peters

A lot tractor can be sold as new (generaly) with less than 20 hours this means it may have been used as a demonstrator or as a loaner while the owners tractor was being repaired! Doubtful that a dealer would put 9 hours on a tractor unless he used it at home!

I do question the 5 year warranty, to the best of my knowledge Kubota doesn't offer that option but a secondary may add to Kubotas Original warranty!!

I would go to another Kubota Dealer and price the same/like unit and that will answer your question as to price!

kubota 4310 hst price
Kubota Tractors
Replies 8 Post by Archdean

I would check your front wheel lugs. I have seen a loose wheel cause some pretty ominous sounds. If that is not it, call your dealer.

JD4310 4WD Noise From Front Axel Drive Train
John Deere Tractors
Replies 12 Post by jdgreen

Sorry for the double post. Just posted this in the owning/buying section then realized this forum existed.<br>
<br>
Getting ready to purchase a rental return unit with very low hours, 35hrs I understand. The asking price is $33,700. Is this in the ball park? Got a $5000 lower quote for the same tractor with around 200hrs from dealer farther away. I starting looking for this tractor from more distant dealers because my local dealer had a buyer for the one above. A few days later my local dealer called informing me the tractor was now available, the deal fell through. I'll be sure to ask why the deal when south but with such low hrs can't see it was something related to the tractor but I'll check. What do you guys think?<br>
<br>
Joseph<br>

Price check 2005 M9000
Kubota Tractors
Replies 3 Post by Joseph_Sulse

Getting ready to purchase a rental return unit with very low hours, 35hrs I understand. The asking price is $33,700. Is this in the ball park? Got a $5000 lower quote for the same tractor with around 200hrs from dealer farther away. I starting looking for this tractor from more distant dealers because my local dealer had a buyer for the one above. A few days later my local dealer called informing me the tractor was now available, the deal fell through. I'll be sure to ask why the deal when south but with such low hrs can't see it was something related to the tractor but I'll check. What do you guys think?<br>
<br>
Joseph

Price check 2005 M9000
Kubota Tractors
Replies 1 Post by Joseph_Sulse

I don't know the crosssover numbers, but I have an AC 5020 that also has a Hinimoto label on it. I think the MF # was a 240? When I see a hinimoto or mf they are exact under the hood.

Hinomot crossover to Massey Ferguson or AllisChalmer
Hinomoto
Replies 6 Post by KosseTX

Don't do it, you WILL break something.

David

JD 855 hydraulics
John Deere Tractors
Replies 3 Post by dsg