Tractorpoint Login

print < Tractorpoint Login

Search for = NORMAN

Topic

diesel fuel in mixed in with the oil. didn't get hot and was running fine when mixture started coming out of oil overflow line.

SD 2200 fuel problem
Shibaura
Replies 5 Post by tutnorman

About 1 year old.

Alternator Battery Regulator
John Deere Tractors
Replies 7 Post by Normando

Mr White.

Thanks for the response. My only experience is with old junk 8n and such. This tractor really seems high tech to me. It is a 4WD. My property is somewhat unlevel and 4WD seemed to be plus for me. Is this 4WD known for issues? It is a 1990 I believe. Any info is highly appreciated.

Thnaks

Kubota L2850 Price
Kubota Tractors
Replies 4 Post by norman71

Frank thank you for the quick reply. Its kind of funny that you mentioned that method becuase that is what I have been doing. I have been draging the low areas with my FEL.

Grader Blade
Operating and Attachments
Replies 12 Post by Normando

I seriously doubt I have a Cat 0 connection. My tractor may be a compact tractor but it is a rather large compact tractor. I�ll get the proper size top link.

Single Shank Subsoiler
Operating and Attachments
Replies 11 Post by Normando

Thank you for the quick reply. Peter the oil that is dripping is not engine oil. The oil is clear to slightly red and my engine oil is brown to blackish.

So if it is the input shaft seal, then I probably will have to split the tractor to get to that seal? If so I should consider replacing the clutch at the same time since I have the tractor split in half.

Leaking
John Deere Tractors
Replies 4 Post by Normando

KThompson, you must have been posting while I was replying. I think you are talking about the same thing I was looking for, Single Shank Subsoiler. I wasn�t sure what it was called, but you describe it as the same thing that someone else had describe to me. I think this would be real effective on smaller stumps.

Stump Remover
Operating and Attachments
Replies 11 Post by Normando

Wow, thank you for the quick reply. I am not bad with welding. But I am starting to get some pricing. After buy the material I am finding completed trailers for less. Pretty amazing.

Trailers
John Deere Tractors
Replies 6 Post by Normando

Thank you for the quick replies. I'll change out the filter and see how it goes.

Peter, I'm not sure where the prefilter is (didn't even know I had one) but I'll look for it.

Thanks!

950 Loosen power
John Deere Tractors
Replies 4 Post by Normando

Ok that sounds great. Do you list his number here or do you want to send me an e-mail?

Thank you.

Funny Noise
Loaders Back Hoes
Replies 8 Post by Normando

Hi Guys,<br>
<br>
I have a JD Model 80 FEL. I have been told that I need to replace the hydraulic cylinders because the ones I have are worn out and the cylinders are scorned. The replacement ones are 400.00 a piece. What do you think my option would be?<br>
<br>
1. Buy the new ones<br>
<br>
2. Buy new ones from somewhere else (not JD)<br>
<br>
3. Find someone to repair them (Not sure if this is even possible)<br>
<br>
I heard of having the cylinders repacked but I am not sure if this is a option because I don�t know what is involved.<br>
<br>
Thank you for all your help.<br>

Model 80
Loaders Back Hoes
Replies 2 Post by Normando

Does anyone know if I can upgrade the hydraulic pump on my 755 to something with a higher flow rate?

hydraulic pump upgrade
Antique Tractors
Replies 1 Post by normank@optonline.ne

Hey guys thank you! That was kind of how I was leaning until someone told me not to bother.

The plating on the rods is in excellent condition. I�ll rebuild them first and see what happens.

Rebuilding a front end loader
Loaders Back Hoes
Replies 4 Post by Normando

Thank you! I'll check that out.

Power Steering Issue
John Deere Tractors
Replies 6 Post by Normando

Here is my two cents.

I have seen this sort of thing on small motors so I think it may pertain. When the air fuel ration is off, the motor will leans out. The governor tries to compensate by either open or closing the throttle, which in turn causes the motor to surge. Either the fuel filter is plugged or the carburetor mixture screws need to be adjusted.

25 hp lawn tractor has RPM surge when run at med hi RPM
John Deere Tractors
Replies 11 Post by Normando

I am looking at purchasing a JD 950. I have been told that the clutch needs to be replaced. I have the mechanical skill to fix it, but I wanted to get an idea of what kind of job this is going to be. If anyone has done this type of work or similar type or work please respond. <br>
<br>
Also if I buy the manual for this tractor will it give me enough information to perform the job? <br>

John Deere 950 Clutch
John Deere Tractors
Replies 7 Post by Normando

Mark,
So what you are saying is that you can shift from high to low range and back to high with no difficulty and can do it while rolling, however between gears say second to third or third to second you should stop. Do I have this correct?? Do the gears work from 1low-1high then 2low-2high etc.. This allows you two ranges for each gear which you can select with ease, basically giving you two speeds for each of the 4 gears for a total of 8???

JD 4100 Gear
John Deere Tractors
Replies 27 Post by Normand

Jeff, I just finished installing a 3rd SCV on my jd4600 and it is not necessary to remove the left rear tire. The installation took me about 6 hours total. The directions are very good. If purchasing a new tractor have it ordered with it as the cost is about the same as I paid for the kit.

Third Selective Control Valve
Operating and Attachments
Replies 9 Post by Norman Grinnell

I have a front end loader on my jd4600 with dual srv. I have ordered a kit to install another srv in order to control the top link on my 3 pt hitch. Has anyone installed this<br>3rd srv on their tractor? I was wondering if there is much to installing this yourself. I'm thinking of doing it myself if not too dificult.<br>Thanks in advance<br>Norm

hydraulic top link
Parts and Repair
Replies 4 Post by Norman Grinnell

I just wanted to update everyone on my problem. The dealer called me back Sat
and appologized for the problem. He asked me if I could come in Monday and redo
the signing of the contract as he had notified John Deere credit to cancel the sale and he couldn't get it reversed, but assured me the price and terms of the new contract would be the same as the original. Even though I don't think the original could be canceled without my consent, I told him I would come in tomorrow to resign. You can be sure Ill compare this new one with the original
to be sure there are no changes. I just hope service won't suffer from this.
Thanks to all
Norm

You won 039t believe this
John Deere Tractors
Replies 14 Post by Norman Grinnell