3point cat 1 conversion to 2inch reciever to accept accessories from
unit5alive
Join Date: Jul 2003 Posts: 250 Latrobe Pa |
2003-05-19 55104
does anyone know where i can get a conversion to convert cat 1 to 2" , inch reciever,so tractor would look like class3 type hitch on truck so i could slide in 2"ball assembly from back of my truck . thanks for any help craig.
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
TomG
Join Date: Feb 2002 Posts: 5406 Upper Ottawa Valley |
2003-05-19 55110
I think places like Northern Tool sell 3ph gadgets that accept standard trailer receivers. To use one, you should ensure that the tongue weight remains less than the 3ph capacity and never goes negative.
A negative tongue weight such as might happen when braking going hill or with a weight shift will simply raise the 3ph and may break it unless the lift distance is limited. I think most of the 3ph receiver gadgets sold do have a chain to limit the distance a 3ph can raise.
You also should be aware that tractor brakes are really parking brakes and aren't that good at stopping with a load. Diesel engines have little engine braking, but HST does provide some braking. Since tractors are much better at pulling than at stopping, there's a chance that a tractor can get a load rolling easily but may not be able to stop it going down a hill.
....
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
TDrock01
Join Date: Jul 2003 Posts: 7 shelbyville, kentucky |
2003-05-19 55113
You may also want to check ebay and do a search on "Trailer Mover". They have some interesting ideas for attaching trailers to a 3-point hitch system.
....
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
DRankin
Join Date: Jan 2000 Posts: 5116 Northern Nevada Pics |
2003-05-19 55117
Here is the best and most cost effective product I have found so far. I have one and it is very well made. ....
Link:
Click Here
 
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
unit5alive
Join Date: Jul 2003 Posts: 250 Latrobe Pa |
2003-05-19 55122
mark do i need the cat 1 26" or the 32" draw bar? (bx 2200) ....
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
DRankin
Join Date: Jan 2000 Posts: 5116 Northern Nevada Pics |
2003-05-19 55125
The 26 is what you need. I would buy it locally if at all possible. No sense in paying UPS rates for an extra 15 pounds. The drawbar probably weighs as much as the rest of the unit. ....
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
RichT
Join Date: Jul 2003 Posts: 33 SOCAL |
2003-05-19 55130
The BXs have a somewhat non std lift arm distance, approx 25in. Wasn't sure if the 26in drawbar would work. Some said yes, some said no. I suspect it would, but I fabricated my own 2in box hitch adapter anyway. Link with pic below. ....
Link: Click here
 
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
TomG
Join Date: Feb 2002 Posts: 5406 Upper Ottawa Valley |
2003-05-20 55145
Spreading the lower link arms and measuring the distance between them might be a check if there's doubt a 26" would fit.
I haven't thought it through but I think that you'd want to snug up the 3ph chains so there wouldn't be much play for heavy loads to jolt the chain mounts at the cases. ....
Reply to | Quote Reply | Add Photo
3point cat 1 conversion to 2inch reciever to accept accessories from
DRankin
Join Date: Jan 2000 Posts: 5116 Northern Nevada Pics |
2003-05-20 55157
The pins on my rear blade are 34 inches and the BX will handle that.
Smaller is better on this machine. Spreading the arms wider pulls them closer to the rear tires.
....
Reply to | Quote Reply | Add Photo
Go Top
Share This