Go BottomNortrac NT204C Tractor 3PH does not lift
 | cdjordan
Join Date: Oct 2014 Posts: 13 ky 
|
2014-10-26 191284
Hello,my tractor lift will work with no load, I can hook up a 5 ft finish mower and it will try but will not lift it, any ideas Thanks
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| Huddleston
Join Date: Oct 2013 Posts: 48 United States
|
2014-10-27 191289
More than likely you either have blown the seal in the piston. Or
The control valve is stuck in the close position. It looks like a nickle stuck on the end of a shaft. It is located on the right side of the mechanism which looks like a rectangle square.
The tractor hydraulic reservoir collects water buildup from the hydraulic fluid getting hot, then the condensation collects to the bottom and covers the control value which had rust inside of the housing where the valve moves in out to let the fluid move into the cylinder which lifts the implement. It the control valve is stuck it will not let the spring, which is on the other side push it back out.
If you can get a large screwdriver and place it down to the valve you may force it open.
Take the seat off and remove the cover, remove the fluid and looked inside where you see the outside control handles move the inside of the control valve using the mechanical bars that push the valve in and a spring pushes it out.
It is probably stuck if not, you will need to use an air hose to blow out the piston to see if the seal is blown.
This is will take you quite awhile to figure out to remove everything. I would take pictures with each motion to make sure everything goes back correctly.
I have placed pictures on this site if you look back you will see where everything is located in the reservoir box.
Hope that helps.
If you don't have a manual, you can find online manual. ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-10-27 191293
thank you ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-07 191356
i looked back and couldnt find the pictures u talked about, what i did do was to loosen the hydralic in going to the block beside the lift lower lever with the tractor running to see if it had pressure. when i loosened the bolt fluid did come out but not like the high pressure u would think, maybe i just think it should be more thank u ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| Huddleston
Join Date: Oct 2013 Posts: 48 United States
|
2014-11-12 191409
It use to be where you could just look at the pictures, however I don't see any of them.
User name is sphuddle, I still couldn't find them.
call me
502 671 1027 ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191536
ok i tried to call u huddleston but no answer, i left message but here are some pics i took of the hydralics,like i said it will try to lift the finish mower maybe an inch off the ground but thats all,i dont know how to get to the cylinder thats inside of the housing. the pics show the front and back, also i took a pic of the quick disconnect, can i check hyd pump pressure here? thanks ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191537
....
Picture Link
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| Huddleston
Join Date: Oct 2013 Posts: 48 United States
|
2014-11-29 191538
If you didn't get an answer, why didn't you place your telephone number on the message page and I would have called you.
Someone sent me an email and wanted me to re-post the pictures.
I resubmitted the pictures and they are on the site. ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191539
....
Picture Link
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191540
i wasnt getting smart or anything with you, u left a message for me to call u about this tractor and i was just saying that i tried, mine is 859- 771-5968, sorry if this sounded like i was trying to be diffacult ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191541
....
Picture Link
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191542
....
Picture Link
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| cdjordan
Join Date: Oct 2014 Posts: 13 ky
|
2014-11-29 191543
huddleston if i saw the right pics u left it looked like you went in through the top under the seat to get to the hydralics far as i can tell i can only get in from the front or back thank you ....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| chaser7
Join Date: Apr 2023 Posts: 2 North Carolina
|
2023-04-12 201552
I am having the same problem, the 3 point hitch will not lift. took the back plate of the distribution valve off and a sher pin in it had broken half into. that valve is the oblong block on the right side of the seat with the activation handle attached to it, the part where the handle attaches to the valve assembly is where the pin broke. can't find the pin may have to buy the entire valve assembly. Don't know if what I said will help but that's my problem. Unless some one knows where to get the pin. the posted diagram show the pin as #29.
....
Reply to |
Quote Reply |
Add PhotoNortrac NT204C Tractor 3PH does not lift
| chaser7
Join Date: Apr 2023 Posts: 2 North Carolina
|
2023-04-23 201564
it has been a few days since I was on here, I found the pin through Affordable Tractor Sales Co. in Bellville, Tx, They have a lot of parts for the Jimna tractors, 3 point hitch works but will not hold weight, working on that now, Anyone got any ideas, Thanks ....
Reply to |
Quote Reply |
Add Photo
Go Top
Share This