Tractorpoint Search for

tractorpoint.com - The leader in Tractors from Compacts, to Utility, to Full Size Tractors! Kubota, John Deere, New Holland, Kioti, Case/IH, and Others. Keywords=Compact Tractor, Kubota Tractors, Kioti Tractors, JD, John Deere Tractors, New Holland, Case Boomer, Used Tractors, Classifieds, Dealer Directory, Tractor Pictures / Images

parts | discussion | photos | podcast | reviews | specs | dealers | classifieds | contact | faq | myProfile | home Login Now | Sign Up

Search for =

Topic

Whenever possible I don't remove the cylinder from the loader. Just the one on the rod end. Then disassemble the cylinder, remove and repair the rod/piston unit and put it all back together. Can't tell by your description, but hopefully the pins you got out are on the rod end.

Seized pins on JCB 506B Telehandler
Parts and Repair
Replies 2 Post by Imfedup

The place to start is at the starter. You will need a voltmeter and possibly help turning the key switch if you don't have long enough leads. You need to take the start signal wire off the starter, connect the volt meter to the lead and turn the key to "start." You need to see at least 10 volts. Any less and the starter most likely will not energize. This condition is what causes the "clicking but not always starting" you read about elsewhere. Your starter works if you supply battery voltage to the start terminal, you've already confirmed that. The switches and related circuits may all be working but even so if the voltage at the end is too low, you get the "no start" symptom. If that's the case, there is a solution to the problem. If you get no voltage at all, then proceed with testing from the key switch on down.

New Holland TC45DA Wont start with the key
New Holland Tractors
Replies 4 Post by Imfedup

[QUOTE=Robertstrach1;201716] I have a 410 loader on a John Deere 4100 tractor. Occasionally it will not lift. It stops at various heights. If I lower it, then try to lift it, som ... [/QUOTE]The parts list for the 410 loader does not show a control valve. Assuming you have a valve that operates it, and it's not on any tractor remote valves, right?

If everything else works as it should, (steering, three point, bucket cylinders, etc) you can pretty much rule out the hydraulic fluid and filters as a problem. Focus on the lift/lower spool of the control valve. Particularly so if it's one of those junky cable controlled versions. Even if it's a simple manually operated single lever style, peel the boot back and observe the ball joints and knuckles to make sure the spool is travelling when you move the lever.

JD 4100 - 410 loader hydraulic problem
Parts and Repair
Replies 3 Post by Imfedup

The power steering on the 235 is well known for problems that are difficult to impossible correct. No argument there.

I believe if it were mine I would approach trading the steering out long before the engine swap thing. Much less work and fabrication. I would look at a unit from 135 possibly. It would involve changing the transmission shift cover and probably some other mods as well. Having never done it, I don't know what all the obstacles might be. Another option might be hydrostatic steering from a 240 or 245 but that would include a different front axle to accommodate external cylinders. No easy way out there.

Engine Swap
Tractor Projects
Replies 6 Post by Imfedup

The relay idea has merit, yes, I've used that trick a few times. It works well enough it the start signal is too weak to energize the starter solenoid.

That doesn't really sound like the problem to me. I think you should be checking and cleaning the ground cable where it bolts to the tractor. That's too good a possibility to ignore in this case.

New Holland TC29D will not start
New Holland Tractors
Replies 7 Post by Imfedup

I did that just a few months ago. I can show you some photos of it if you'd like.

Need a new scv bucket loader control valve for a late-1086 jd 850
Tractor Projects
Replies 3 Post by Imfedup

I'm not sure why that would be.

Nortrac NT 404 hydraulic problem
Jinma Farmpro Agracat Nortrac
Replies 5 Post by Imfedup

Actually never owned one, but spent some years at a New Holland dealership. I got to know the Ford line pretty well.

5610S Ford New Holland does not start
New Holland Tractors
Replies 10 Post by Imfedup

Do you think a 205 might have a Perkins engine?

Massey Ferguson 205-4 starting and power problem
Massey Ferguson Tractors
Replies 20 Post by Imfedup

[QUOTE=Murf;200925] When it comes to hydraulics the only real cause of heat is work, the more work, the more heat it creates. If you have not already done so, I would suggest you take a careful look at the power steering box. It is the only other piece left in the circuit. That’s a leaking internal seal will not be evident because the fluid is merely circulating back to the return line. However, the friction as it leaks past the seal will work very much like a partly open relief valve and cause excess work and therefore excess heat.It’s a simple easy thing to test. Best of luck. [/QUOTE]
What exactly are you suggesting he test? And just how would he perform this test? You have my curiosity up now.

MF 135 ps overheated
Massey Ferguson Tractors
Replies 6 Post by Imfedup

The shims would be in the diverter valve block. Apparently the relief valve will vary some depending on tractor serial number.

https://www.mycnhistore.com/us/en/newhollandag/tractors/compact/naba17003tc/3-cyl-compact-tractor/hydraulic-systems/manifold-diverter-block-sba340015500/cn/03795BBA-B8BF-E111-9FCE-005056875BD6?m

Shim kit for New Holland TC30 w7308 Loader
New Holland Tractors
Replies 2 Post by Imfedup

Slow moving site. Requires patience.

Mitsubishi D2350 rear lift hydraulics
Mitsubishi
Replies 17 Post by Imfedup

I wasn't suggesting the starter to be the problem, only that hearing it engage and operate would eliminate a cable/connection issue and take you back to wiring and other circuits.

2001 NH TC33D will not start no power
Other Tractor Brands
Replies 11 Post by Imfedup

So when is tomorrow? How did all that work out?

MF451
Massey Ferguson Tractors
Replies 8 Post by Imfedup

Okay. Are you aware that the live pto and hydraulic lift pump both drive from the same source. When the pto portion of the clutch is disengaged, both of them stop turning, not just the pto shaft. If you now find that neither is working at all, your problem could be in the clutch itself. Have you removed the cover plate from under the bell housing and looked for anything unusual in that area? You may find fragments of clutch lining and/or other evidence of disc or clutch failure.

mf 255 pto and 3pt lift not working
Massey Ferguson Tractors
Replies 5 Post by Imfedup

The relief on your system is in the divertor block located on the lower right side of the tractor. This is the block with three lines leading to the loader valve. It is shim adjusted, so if it's set too low you will need to add shims, not just turn a screw. You will first need a pressure gauge, at least a 3000 psi, and a fitting to match one of the hydraulic couplers on the tractor(or the necessary fittings to "tee" into the pressure side of the system). Your choice here. Once you have established the current relief valve pressure reading you can plan your next move.

Adjusting the 7308 pressure relief valve
New Holland Tractors
Replies 3 Post by Imfedup

I can't promise that I'm capable of sending it, but I can try. The person who sent it to me said I might need a Gmail account to receive it. My Email happens to be with Gmail, and I had no trouble receiving it. If you give me an address, I will give it a try. You can send it by private message if you wish.

New Holland TC26DA starter problems
New Holland Tractors
Replies 7 Post by Imfedup

Noise in that area is NOT normal, nor should you continue to operate it before determining what it is. I would imagine the "adjustment" had something to do with the clutch pedal travel/freeplay. Whether the pedal is up, down, or somewhere between when you hear the noise may help narrow down what's causing it. If the noise(or something similar) was there before purchase, then you and the "dealer" have something to talk about.

Long 2360 noisy transmission
Long
Replies 19 Post by Imfedup

I have not yet been into the governor on one of those engines, so I have comment. I will say that to the best of my knowledge it's somewhere under the front cover, nestled among the timing gears.

Branson 4220 racing problem
Other Tractor Brands
Replies 15 Post by Imfedup

Most Long tractor hydraulic pumps will be a tapered shaft with a woodruff key. Probably about 7 GPM.
Depending on the model, it may have either a metal suction screen or a spin on filter in the suction line. Have you serviced that?

Long 460 hydraulic question
Long
Replies 8 Post by Imfedup