Tractorpoint Search for

tractorpoint.com - The leader in Tractors from Compacts, to Utility, to Full Size Tractors! Kubota, John Deere, New Holland, Kioti, Case/IH, and Others. Keywords=Compact Tractor, Kubota Tractors, Kioti Tractors, JD, John Deere Tractors, New Holland, Case Boomer, Used Tractors, Classifieds, Dealer Directory, Tractor Pictures / Images

parts | discussion | photos | podcast | reviews | specs | dealers | classifieds | contact | faq | myProfile | home Login Now | Sign Up

Search for =

Topic

Kenny,
Thanks for the reply. Just went out with the flashlight and found the problem. the spring you discribed matches one I found in the yard last week. Just gotta figure out where it goes. I found a lever under the trans cover on the right hand side just in front of the seat . It was pushed foward. It has a strike plate on the top that acts as some sort of safety for the Operator on seat lever and trans. high/low/neutral lever. I pushed this lever back and now all is well. I suspect the spring helps this return on its own. It probably wasn't a problem until a limb knocked it out of position. I need to get real intimate with this mechanism, found some loose linkages that need tightening. If you want to run the 1/4 mile, shove this lever foward. I think I could do 0-60 in 5.2 sec. Will definately drop by the dealer for that manual tomorrow.

thanks again,
and thanks to all who have posted in the last 3 months for the wealth of information provided.

Reg Waters

JD 755 hydro drive problem
John Deere Tractors
Replies 3 Post by Reg Waters

What tractor do you have. What attachments did you get with it. What age is your tractor???Just trying to get this forum going again!

List which tractor you have Ventrac Steiner
Garden Tractors
Replies 19 Post by Ricky

I have recently observed several new compacts 4200 to 4700 on dealer lots in three different states. I was supprised to find many units with the old axle design. If you have a JD product catalogue for 4000 series tractors, look on page 4 at the top view of the displayed machine. Closer inspection reveals one hydraulic cylinder attached to the right front wheel and a tie rod connecting both front wheels.(new design) In a previous version of the same catalog, page 4 displays another tractor (top view) with I think a double acting steering cylinder attaching to both front wheels, with no connecting rod.
I hope this helps. BTW I elected to order from the factory (3 week wait) rather than buying from inventory on the lot.

4XXX Front Axle Issues
John Deere Tractors
Replies 8 Post by Rick Johnson

I have a Ford/NH 1215 with only 300 hours on it. I've had no problems with the tractor yet and I work the heck out of it considering its size. I've run a 48" Bush Hog, 48" belly mower, york rake, 60" back blade and single bottom plow, all with no problem. I recently installed a Great Bend 220 Loader on it with a 48" bucket, again, no problems, although I usually carry a counterwieght on the back when doing heavy loader work. 4WD is a must. I do not have PS, which would be nice with the loader. Keep in mind these tractors are small, only 16 HP. You may have problems with bigger implements. I rented a 60" rotary tiller which was too big for the tractor and forced me to make several passes to get to the depth I wanted. My neighbor has a 1210 which is basically the same machine. He has over 1200 hours and has had no major problems.

Info Requested on Ford New Holland 1200 Series
New Holland Tractors
Replies 4 Post by Paul

Jeff, got one from Harbor Freight as well. It really works well. I dodn't realize it was such a bargain until I saw the prices posted here.

Lubrication
Parts and Repair
Replies 4 Post by Eddie Watkins

I don't know if you are talking to the janitor or not, but Bradco is a line of high end backhoes. For years they have been a brand that a contractor would buy, but were more than a compact tractor owner wanted or needed. Bradcos are heavily built and high priced. I have no idea if they make the Woods....or if they do, if it is made to the same standard as the rest of the Bradco line. For all I know, Bradco may be making several different weight of backhoe today. All of the older Bradcos that I have seen were painted black and are clearly built of heavier metal than homeowner hoes. They are popular as skid-loader attachments. I very much agree with the frame mount. For bucket size I'd recommend a 12 inch if you have any rocks or stumps. Maybe a 15" if you just cannot talk yourself into the smaller bucket. No larger.

Bucket size
Loaders Back Hoes
Replies 3 Post by Roger L.

I have 4300 4WD HST with 430 loader. I would highly recommend having as much rear weight as possible when the loader is attached. Last week I almost rolled over when going down a steep hill with empty loader, no ballast and 2 wheel-drive mode. The weight of the loader caused the back wheels to lose all traction so I had no brakes. The tractor simply took off coasting down the hill as fast as gravity could pull it and I had no way to stop it! Take my advice and have fluid put into your rear wheels, attach a ballast box or other heavy rear implement, and also use 4WD when the loader is attached.

JD 4300 Winter Items
John Deere Tractors
Replies 17 Post by Chuck

David the coat was 17,525 delivered price. we are in centeral Oklahoma.
Also got the foldable rops. I have no regrets, love the tractor.

Kubota B2910
Kubota Tractors
Replies 4 Post by carl

Jeff,

Interesting question, I assume your Johnson switch is only the manufacturer, Johnson Controls and that the switch in a simple RTD or thermoswitch. Do not own this tractor but would assume if you have any wiring charts for it that they would indicate the switch and cut-off scheme. Any JD fans out there with better info?

Jerri

Johnson Switch
Parts and Repair
Replies 2 Post by Jerri Neese

As a former JD Consumer Products mechanic, I've had to rebuild several 55 series front ends. From what I have seen, it appears that when using the loader, people inadvertently end up with the front wheels off the ground at times. After noticing this, they lower the wheels back onto the ground while still trying to dig, sometimes jamming the front wheels back to the ground. The proof is the damage done to the snap ring groove for the bearings in the knuckle casting. If you take a close look at the design of the axle pivot area, you'll notice that the tractor is supported by the short vertical stub drive shaft, which is not a very good design in my opinion. I owned a 655 with loader and had oversize tires on it and with over 560 hours & no failure, it's because I was careful not to drop the front wheels on the ground, especially when trying to dig, and I worked the tractor well above the limits that Deere had in mind for it.

breaking teeth on gears in front axle on a john deere 855
John Deere Tractors
Replies 18 Post by Stan_McC

Ridge Runner--having had several major repairs made on my 4400, I am in full agreement with you in all regards--especially the extended warranty. I have even wondered if there were enough needed major warranty repairs that a class action lawsuit might produce some results. Also--if it takes JD 20 months to get all of the warranty and PIP issues taken care of on my tractor, it would only seem reasonable to provide a longer warranty. While visiting with a representative of a JD dealership that only sells the big ag tractors, I was told that JD backs their major repairs on new tractors with a 2 year warranty on those repairs. While I cannot confirm this, it is of interest and I would be interested if anyone else has had the opportunity to see if JD does unofficially extend the warranty on major repairs. Mike S.

meeting john deere augusta
John Deere Tractors
Replies 38 Post by Mike S.

Duane, I sure don't want to start a war of words on which brand is best. I guess that might be like discussing whether a Ford or Chevrolet pickup is best. I would hope that everyone is happy with the brand they bought, and that's what counts. But for me personally, I looked at John Deere, Ford/New Holland, Cub Cadet, Kubota, International, and some lesser known brands, new and used, in 1995 for 6 months before buying a Kubota (I started that search with John Deere being first choice). In 1999, I didn't even look at anything else when I decided I wanted a little bigger Kubota with some additional features, especially the power steering, flat floor, and position control on the 3-point. And since I live in farm country, have spent some time helping neighbors with other brands of tractors, big and small, and have been reading messages on the discussion forums, my conclusion (whether right or wrong) is that the Kubota is the most reliable, trouble free, best buy for the money, and most of the features I wanted are standard equipment; not options. And if owners of other brands disagree and feel they have the best brand, I'm happy for them.

JD4100 vs Kubota B7500 HST Dealer Impressions
John Deere Tractors
Replies 7 Post by Bird Senter

Is anyone aware of a simple and reasonably priced snow blade setup that could be mounted on the loader arms in place of the bucket on a N/H tc29 tractor? Any experience with rear mounted snow blowers or other implements that facilitate cleaning a 200' long stone driveway in the North East. The rear blade has been a bit of a pain on other tractors I have owned, it seems they pull just so much snow then fill the area between the blade and tractor necessitating stopping and moving the load with the loader or snow plow. Thanks!

SNOW BLADE
Operating and Attachments
Replies 1 Post by cutter

If you are purchasing items from out of state you do not pay sales tax to that other state. If that company has an office in your state they will collect sales tax for your state, even if you purchased from a location across the border (assuming that your state has sales tax, are there any left that don't?). Most states, that have sales tax, have a law which says that you have to pay sales tax/use tax on items purchased out of state unless you already paid more than what your state collects for sales tax.

I'm not a lawyer and don't give legal advice, but here in illinois the only advantage to buying out of state (assuming that you report your out of state purchases) is that you might avoid paying city or county charges. For instance, the state of Illinois has a sales tax rate of 6.25% but if you buy in the city of Chicago (who would buy a tractor in the city of Chicago?) the rate is 8.75% due to city and county taxes. These taxes, last time I looked, are not collected on the state income tax return for out of state purchases.

DavidV

Should State Tax be paid on out-of-state tractor purchases PA to NY
Parts and Repair
Replies 5 Post by DavidV

I think you forgot to mention what the price is.

JD 850 price
John Deere Tractors
Replies 4 Post by Larry in MI.

Chuck; A couple of questions. What are the specifications (bucket size, digging depth, reach)? Is it owner setup-able? Do you ship? And, if so, what is the ballpark price (recognizing that shipping cost is mileage dependent)? Thanks.

BX Backhoe
Kubota Tractors
Replies 8 Post by Roy

I have a woods 6ft 3pt finish mower on my 4400 hydro and you don't even know i'ts back there.

4300 vs 4400
John Deere Tractors
Replies 25 Post by pj

I'm considering buying a Wallace bush hog from TSC (Tractor Supply Company). Has anyone owned one or know anyone who has? I'm just wondering how they compare to King Kutter. Both brands are in the same price range. Thanks.

Wallace bush hog from TSC
Mowers Field and Finish
Replies 1 Post by Danny Yerks

I'm considering buying a Wallace bush hog from TSC (Tractor Supply Company). Has anyone owned one or know anyone who has? I'm just wondering how they compare to King Kutter. Both brands are in the same price range. Thanks.

Wallace bush hog from TSC
New Holland Tractors
Replies 1 Post by Danny Yerks

MY 4300 CAME WITH THREE STRIPPED OUT BOLTS ON THE LEFT REAR WHEEL THAT WORKED LOOSE CAUSING WHEEL WOBBLE. PROBLEM WAS REPAIRED UNDER WARRANTY, NO CHARGE.

4300 wheel bolt problems
John Deere Tractors
Replies 72 Post by ridge runner