Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Thanks, cowrider. Do you know if there is another port on the hydraulic control assembly to accept the second line?

Kim

Rear hydraulic outlet-settin up hydraulic top link
Belarus
Replies 5 Post by IvanT25A

You should replace the fuel filters instead of just looking at them. I had a Mercedes that would run just fine until I went up a hill of put a load on it. Turn it off for a few minutes and it would work again. Seems that the filter picked up dirt while fuel was flowing when running and then would fall of when fuel stopped flowing. Never had another problem after replacing the filter.

As another had said, check the piston cylinders. Pull the cover off the side and clean out anything from in there. For some reason here the mice love to build their nests inside my covers when the tractor sits without being used.

The temp sensor is on the oil filter

belarus 400 shuts down after running
Belarus
Replies 5 Post by cowrider

That's the easy part. From your sediment bowl the line going to your injector pump has a screen down at the banjo fitting. Just take the bolt out at the pump and you will see it when you take the line off.

nt204c fuel issue nortrac
Jinma Farmpro Agracat Nortrac
Replies 7 Post by bogman

If you have a volt meter or a test light you can check at the starter that you have power there. Make Sure that it is out of gear and brakes applied/chocked. You should have power at the large terminal at all times, small terminal when switch is in start position. If nothing then check battery terminals and ground. Another check is to use a remote start switch or heaven forbid a screw driver from the battery terminal on the starter to the small terminal, this should engage the starter.

Do you have a manual? I found this one
http://www.jinma-tractor.com/download/JINMA20-30A.pdf
it has a wire diagram

Nortrac 254 will not start
Jinma Farmpro Agracat Nortrac
Replies 3 Post by cowrider

Post a photo of the shifter and we will try to figure it out for you. I get lost after a sentence.

Leda T30a Belarus shifter questions
Belarus
Replies 2 Post by cowrider

My tractor has been sitting idle for a week, it has never had a problem starting, and now it will not even make a click when I turn ignition. Nothing. I changed the battery since it was old and checked the fuses. Still nothing. Could this be the solenoid or the starter?

Nortrac 254 will not start
Jinma Farmpro Agracat Nortrac
Replies 1 Post by Vet103

Brian I am having the same issue with my 790, about the same hours, left front gear box. Had the right replaced under warranty when it had about 30 hours, but there were more issues than a leak on the right. Can you advise what you went thru on repair? Thanks Bernie

790 4x4 front axle leaking
John Deere Tractors
Replies 5 Post by bernieb

My 1070 is starting to have problems staying in 4Th gear. It seems like the shifter is hitting the back of the selector housing so it can't fully engage 4th gear. Can anyone tell me how to adjust the linkage?

1070 Case Transmission Linkage
Case
Replies 1 Post by LarryG

OK, the supply line from the tank had a hole in it so it was sucking air. I replaced the supply lines and its running OK now. However, I couldnt get it to move. So I got scared and thought the clutch was bad. But after fidding with the F-R lever and the gears it finally moved. Im off to pickup some Hydraulic fluid now.

Leda T30a starting issues
Belarus
Replies 7 Post by tractah

Ann,<br>
<br>
It is so good to hear from you, and that you are still living your dream.<br>
<br>
Dennis

Howdy Tractorpointers
Parts and Repair
Replies 6 Post by DennisCTB

The wrong oil will give you a lot of grief as well as potential costs later.

Hydrostatic drive trouble
Massey Ferguson Tractors
Replies 4 Post by Art White

Not sure how many hours are on the tractor. I had bought it on Ebay from a couple of fellows in Ohio and it was inop. It had a mess of problems when I got it home, injection pump was messed up, injectors buggered up, fuel lines bent up and other problems I try not to think about. When I finally got it running it had lots of blow-by, so much you had to pay close attention to the oil. But it ran well and had lots of power, just hard to start sometimes. I think that someone went heavy on the ether trying to start her. You should never have to use ether on these tractors with it have the decompression lever.

I just replaced the pistons and rings, used the original cylinders, no damage to them. Just ran a hone through them.

Belarus 250as blowby
Belarus
Replies 8 Post by cowrider

Good day all, I am in need of some help with My TD5050 Hydraulic system. The hydraulics has stopped working, to include loader, and any hydraulics, steering is sluggish at anything above Idle. I bought the tractor used 3 years ago, and it is a 2008 model. I changed the hydraulic oil, found metal particles on the Mag plug, so I also changed the hydraulic pump as well. The pressure has improved slightly, but still very sluggish as it was before I lost all hydraulics. Please help.<br>
<br>
Thanks

TD5050 Hydraulics not working
New Holland Tractors
Replies 2 Post by skeeter

thanks WillieH. I'll let you know how I make out.

Leinbach L7200 Post hole digger oil seals
Operating and Attachments
Replies 3 Post by JFagan

Is there'a simpler to replace the secondary clutch buttons without disassemble the clutch? If there is I need some help on my gator. Littleon

Secondary clutch buttons
Utility Vehicles UTV/ATV
Replies 4 Post by Littleone

Does it have a KE130 motor?

Mitsubishi D2000
Mitsubishi
Replies 7 Post by lsheaffer

When lifting bucket or tilting bucket solely the bucket hydraulics work fine. However, if we tilt AND raise/lower the bucket at the same time the hydraulics quit. Has happened twice. First time we let it sit for 2 weeks - tried it out and everything worked normally for months - but then got in a hurry and made the mistake of tilting and lifting the bucket at in the same motion and hydraulics died. Been dead since.<br>
<br>
I'm thinking it could be a pressure valve problem - what do you all think?<br>
<br>
Any ideas?<br>
<br>
Thanks in advance for any help. We've checked the hydraulic fluid levels and quality - they appear normal.

JD 72 1520 Hydraulics
Antique Tractors
Replies 2 Post by cdedmon

Check your fuel cap to see if that is working properly.

Kubota 4750DT Fuel Venting
Kubota Tractors
Replies 2 Post by Art White

you can email me at" parts at sheaftractor.net"

Radiator hoses
Shibaura
Replies 5 Post by lsheaffer

For decals you might try the dealer. Kubota does have some decals available as far as I know.

decals for 2000 B7500 DT TLB
Kubota Tractors
Replies 2 Post by dtk1952