Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Well an update. I did buy a 10 foot pull type box blade product of Lowery in Alabama. It has of course a lift but also tilt using the right wheel to raise or lower the right end of box blade which makes sense since that is the side the lift controls are on tractor.

I have used it a few hours and have a 90 some hp four wheel drive JD and it a good load for the tractor. Depending on what you are doing will over load the tractor but not often so far. I have been able to cut down reasonable hard clay and to pull full box blade amount of dirt reasonable well. It is not a set it and forget system at all for you do use the main lift to slowly deposit extra dirt when building up an area.
Is it better than box blade on the 3 pth hitch...well it is longer and does better job taking down high spots and filling low spots compared to blade on the lift by far. It does not track as well around outside of curve for it is a trailer and will track inside the curve. It cuts much better than my 3 pth bb did and it holds almost 3 times the dirt my 3pth bb does.
Would recommend it to anyone who has real dirt moving or leveling needs.

Pull type box blades
Operating and Attachments
Replies 9 Post by kthompson

Is this the first one to use the rack? Who designed the rack them or your company? If they have used it in other locations with no problem why concern now? kt

Concern for building stability
Barns Pole Barns
Replies 6 Post by kthompson

have a Chinese rhino tractor. I cant lift the front bucket unless I hit up on the 3 pt to raise it? anybody had this problem any suggestions? it started raising and lowering slow and then just stopped? 3 pt works very well and so does power steering. had the spool valve out today looked fine and only 2 orings. the bucket will tilt up and down.

rhino tractor
Other Tractor Brands
Replies 1 Post by HAYDEN6984

Would anyone know the metric size of the original 950 sending unit for the temp light. My gauge conversion project is held us as I can't find the metric adapter that will fit. Thanks

john deere 950
John Deere Tractors
Replies 7 Post by cwsull11

My tractor just started venting fuel out of the vent tubes and I was curious if someone had experience with this issue?

Kubota 4750DT Fuel Venting
Kubota Tractors
Replies 2 Post by barber1189

Those 8n's with front distributor are known for problems with the coil, so i would recommend you replace the coil it is likely the problem even if you get fire at the plug i helped a friend just a couple weeks ago with a problem similar his would run but run terrible ]then quit then start again. good luck ron

Engine Won t Start
Antique Tractors
Replies 6 Post by flagman

I own a New Holland Tn-60-A 60 H.P and just spent over $12,000.00 to get the transmission fixed.I think N.H. is Junk all of them.

TN 75s AC bower
New Holland Tractors
Replies 2 Post by 46bugs

Hey guys new on here! TN75 S AC blower only has high speed and recently blowing the 25 amp fuse. I was told to take roof off to get to blower motor and resistor. Cool except I don't see any bolts outside roof? I read somewhere you did t have to remove headliner another thread said you did? Any suggestions? <br>
Thanks in advance,<br>
Tripp

TN 75s AC bower
New Holland Tractors
Replies 1 Post by Tripppruitt

1 Year and two months.
My most major annoyance is the 90 or 60 day in site repair service. It is flat out not happening period. Almost a lie. Good selling point but not true at all.
I fixed the hood once the new latch arrives. The Lath just would not hold I don't see how it ever could. The old latch was defective the new one did work but as with the first one was to far away from the rod on the hood, There appears to be adjustments on the very back of the hood to move the hood around but they were already as fat as they would go. I cut a piece of treated wood 1/2 inch thick as a spacer. Laced it between the frame and the new latch. The hood now latches and stays down, This is a issue that the factory should look at. I cannot be the only one that had this.
Minor Issues. Pin that makes the lift leaver work drops out.
Fixed with a new pin.
Pin in 4wd pull handle fell off. Fixed
Pin in the Shuttle shift Leaver fell out. Tore the rubber boot covering the Front amd rear select.
Low Speed PTO speed wont work, Even though it had never been used, I was told to adjust the clutch. Common issue.I do give the Phone support staff at Nortrac 4 stars, Their advice have been great,
Driving to the Service center It seem they don't want to fool with it,
The tractor Has done everything I have wanted it to do. Still happy with it
Bottom Line Great Price,But you had better be handy with tools and have some mechanical skills.
If you buy one Day one PTO,LIFT,4WD and the Hood Latch check it when it comes off the truck. Have a set of needle nose pliers and some real thin stainless steel wore,
I have found a thin piece of wire through the pins twisted at the ends will hold the pins in place, The Cotter pin used to hold the 4WD pin in place is week in my opinion, I bought some at TSC and I think they will hold better.
Clutch adjustment not done yet I will post how this goes.

NorTrac 35XL Northern Tools Foton I think
Other Tractor Brands
Replies 17 Post by Gameman

I contacted the mechanic at the branson dealer in Simpsonville,KY because the local guy didn't seem sure about the problem. The mechanic said he had never had to change a injector on a branson! He told me to have the local guy try a part can of transmission fluid thru the fuel pump to try to loosen up what might be sticking. Didn't work.he even Reyes Seafoam. The local guy was not happy that I asked someone else...he said he had changed many injectors. So I had them bring it back to me as I was going on vacation for 6 weeks. So here I am back without a tractor. I may try checking it out myself as advised above. Is there any step by step instructions out there? How about a part number from someone who has a manual?

Branson 4220 racing problem
Other Tractor Brands
Replies 15 Post by bobs4220

Most likely a spec of dirt in the relief valve in the control valve under the lift housing. Before disassembling measure thread lengths.

Mitsubushi D2650FD tractor box blade won t lift
Mitsubishi
Replies 3 Post by lsheaffer

Ran into this Saturday on fel as the hoses came lose while using the tractor and the weight of the bucket put load on the hoses. Was not near wrenches but was near excavator. We took the excavator and picked up a little on the bucket and that was the end of the pressure issue. Please note the other hose had already been reinstall. Both were pulled off in working on dirt pile but only the up hose really was any issue. kt

Release of Hydraulic Pressure
Kubota Tractors
Replies 17 Post by kthompson

Right before they go metal to metal or if one breaks. If one breaks always replace all of them. Actually, always replace all of them.

Secondary clutch buttons
Utility Vehicles UTV/ATV
Replies 4 Post by gatoraider

I would like to howI can tell if or when the buttons needs to be replaced.

Secondary clutch buttons
Utility Vehicles UTV/ATV
Replies 1 Post by Littleone

Belarus 400an, air cooled, diesel engine. Initial start up is great, idles and throttles correctly.<br>
while in use will run for an hour to 2 hours and then just shuts down. wait about 20 minutes and it will start up roughly and then come to idle great and run again for the same amount of time and shut down again. I then ran tractor stationary for a couple hours with no shut down, so I decided to hop on it and drive it through the field and then it shut down. I pulled the fuel filters and they seem fine(it has 2). Drained fuel tank and found very little debris. Oil changed, air filter checked/clean. (oil bath with sponge prefilter). changed oil in fuel pump. fuel lines seem solid, belts good, mechanical fuel injected. its a 1997 I believe with less than 300 hours. I don't know where to look next to see why it shuts down. Any help would be appreciated. Thanks.

belarus 400 shuts down after running
Belarus
Replies 5 Post by molealma

Nope 8-)

I believe (?) that the B1700 and B7300 are quite similar in that the layout is similar if not the same, only real difference being the tin work.

If you remove the left side rear tire and wheel assembly, you'll see two hard line hydraulic lines mounted to a block, via a couple of fittings, as well as a bracket on some realizing a strain reducer. The o-rings are nestled behind this block. Not a clean job, rather oily as you have to disassemble the lines and such, so have rags and/or drop bucket below to catch the fluid. Realize the o-rings, reinstall the block and brackets, then the lines. Top off fluid to account for the fluid that drained out, and you're off to the races. Before you reinstall the wheel, swab everything down REAL good to insure dryness . This way, in case there still is a leak somewhere, you'll be able to realize where it might be coming from. Not saying that this IS your issue, but sure would be an easy and inexpensive way out! Just some time...which we all have LOTS of. HA!

Best -
Willie H.

B1700 Hydostatic unit leaking
Kubota Tractors
Replies 7 Post by WillieH

It is a shibaura Sd2643 similar to a Ford 1910 but the 3 point lift system has an electric selniod instead of mechanical linkage.

3 point hitch linkage
Shibaura
Replies 8 Post by Fltpicker

I have learned to never underestimate Murpy.
Thank you for the complement.
Arc.
:)

New Holland TC55DA 4 wheel drive tractor Boomer series
Parts and Repair
Replies 8 Post by arcwelder

I am still looking for the left side of the hood for a 2360 Long Tractor.
Any help out there?

Thanks

Long 2360 noisy transmission
Long
Replies 19 Post by 46bugs

Thanks
And it works just fine.

375 Backhoe - New Pix by Radoubs
Photos
Replies 3 Post by Radoubs