Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

So I'm having a fuel issue. I've changed all the lines from fuel to vacuum. I can put had in the carb, and it will run until the fuel is gone. I can see the filter fill worth fuel but it seems like no fuel is going to the carb. Any thoughts would be a help.<br>
<br>
Joe

Cub Cadet 3185 fuel problem
Cub Cadet
Replies 2 Post by Heavy60952

The female connector housings on the wiring harness that connect to the headlight pigtails on the grill have gone the way of old nylon. These are 3-pin things using standard 1/4"/6.3mm quick-connect blades. No markings on the connectors (of course).<br>
<br>
I found a web reference to the Stanley PN 001-1726 on the headlamp socket/pigtail assembly that implied these were also used on a JD 175.<br>
<br>
Anybody know of a source for the connectors or connector housings?

Replacement harness headlight connectors - CC 7305
Cub Cadet
Replies 2 Post by chashm

with some help from other source trying to confirm this info before i dig in. injector pump was taken off with out noting timing marks. this is a 1987 taishan 30 hprse power diesel. talked with someone and here is what he said. on the injector the front line (there are 2) hold your finger on the opening and turn motor over by hand until you feel pressure. then pull gear off pump, pull top motor cover off and turn motor over by hand until both valves are open and then turn motor back 12-14 percent and then put gear back on pump and reinstall motor cover. does any of this make sense. thanks

taishan 304 diesel timing
Other Tractor Brands
Replies 1 Post by bemike61

Im going to go ahead and order a new one along with a new
rubber collar. Like you say I will see how it goes
onto the the tractor too. I have to have a new one because
my old one is worn bad on the top of the hole.
Will let you know what the new one looks like and will send pictures of it back side etc.

Found my one part and looiking for some anothers
Belarus
Replies 19 Post by videorov

Well, it wasn't the switch. A guy let me test with a new one. Same thing. A loud thump/click every time I turn the key, then finally it will turn over and start. Still no electrical at all. Does the relay do anything besides the glow plugs on a e2004 and is there a solenoid to check? What about an in line fuse on a e2004?

no electrical on Hino E2004
Hinomoto
Replies 13 Post by Lowery

I think you do good to talk to someone who can do the work and get their idea and pricing.

Lawn renovation
Garden and Landscape
Replies 9 Post by kthompson

Getting ready to install new clutch/pressure plate. Manual says to check release levers height using gauge #NH1300. This gauge looks easy enough to make , does anyone know the difference in height between the outer legs and the center tab? Tried two local dealers, no help there. Thanks.

TC25 Clutch Replace
New Holland Tractors
Replies 1 Post by icebite1

NOTE: Title should read TC25/25D , Cant edit title.<br>
Installing new clutch/pressure plate and manual says check release levers height using tool NH1300. Tool looks easy enough to fabricate but does anyone know the height difference between the outer legs and center tab? Tried two local dealers but no help there. Thanks

TC2525D Clutch
New Holland Tractors
Replies 1 Post by icebite1

No idea why I thought your tractor might be gas, brain freeze I guess. My manual does give decent details on priming but I always fill the fuel filters as full as I can, crank and then run it at least say 1500 rpms and it often will keep on running through any air left in there. A good note to know is WD 40 is very good starting fluid for a gas or diesel engine. Remove air filter and use burst of WD 40 while cranking it. Even if air in fuel system it will crank on it and keep using short burst while it is running till it runs steady.
What oil the manual says to use in front end not sure but if had option to use the same as in trans I would. I have a super duty manual transmission in Ford pickup and it uses ATF fluid. The clearance on machined parts is much tighter than years ago.

Do want to share a warning with you or two: hyd oil is running under say about 2,000 psi, be very careful with leaking injecting oil into your skin and cutting you. Also if you have a leak in that system it can drop your transmission level very quickly and give you a costly repair (I had this to happen). Also if not already covered do not run in 4 wheel drive unless on say gravel or dirt. On such as concrete or paved road can damage the four wheel drive system. The front wheels run faster ground speed than the rear wheels so the front wheels needs to be able to do some slipping. be careful and have fun. If you don't have a canopy on the tractor it sure is nice in the sun or rain or in hail. Do not play in lightening.

Kubota B2710 New to meadvice
Kubota Tractors
Replies 11 Post by kthompson

Possible ignition wires put in wrong position on distributor cap. A GM dealer did that to my car doing a broken timing belt repair. The mistake caused broken valve rods etc..<br>
<br>
Could be installed wrong kit...

Ford 8N Electronic Ignition Installation Problem
Antique Tractors
Replies 4 Post by DennisCTB

Kenny, the pumps we use have an open center. If you use a PTO shaft extension you can run two pumps in tandem.

Best of luck.

pto sprayer pump s volume
Tractor Projects
Replies 13 Post by Murf

Sorry I meant if your arms aren't long enough to push the pedal while looking have a friend help by gently pushing reverse while the tractor is not running and on level ground

RIOS switch on JD-LT190 Lawn Tractor
John Deere Tractors
Replies 18 Post by Mattw84

I received a notice of post today, but do not see
Call me
7five7-434-331zero

914A 60 mid mount mower deck for sale in suffolk va 2002 model
Mowers Field and Finish
Replies 12 Post by Bick333

Turns out I can order one from a local Woods dealer. A 9" for not much more than a Prairie Dog one.

The Woods dealer can get one to him for me for $350.

Prairie Dog wants $325 plus shipping for an 8".

Makes sense to go with the brand name since the guy above says the PD didn't fit right and was oddly shaped.

praire dog backhoe
Loaders Back Hoes
Replies 10 Post by gerrybc

I was concerned at first because my backhoe attachment (Brands) is a three point attach. I have dug 600' 4' to 4 1/2' thru reclaim. I hit 15 to 20 foot of a buried road bed that was set with rip rap and pack as hard as concrete. I had another section of about 15' of dirt like coleachy, it was so hard the only way to get it was pointing bucket teeth down and raise bucket full hiegth and slam it. I have another 1200' to dig and so far I've been really pleased, nothings broke. I've worked this as hard as you could possibly work a backhoe attachment and tractor and hoe have both held up good.

Update - Backhoe Attachment
Loaders Back Hoes
Replies 2 Post by yocsr1

Does anyone know if a 6x4 4x2 HPX driven AM138486 has the same moveable sheave as AM140967 4X2, or if the whole assembly is compatible?<br>
<br>

Driven Sheave cross reference
Utility Vehicles UTV/ATV
Replies 1 Post by Coachlarry

1200A Bunker Rake Shudder under load
Utility Vehicles UTV/ATV
Replies 18 Post by Coachlarry

Allis Chalmers orange turned out to be a perfect match.

Hinomoto E2004 paint code
Hinomoto
Replies 4 Post by Lowery

[QUOTE=gatoraider;195141] If this is the picture of what you have, it is not a K35 it is a K30 and it is a bunker rake K30 because there is a brake disc on the side. No other K ... [/QUOTE]

Just went to look at it again and you are absolutely correct about it being a K30. And yes, it has the splined shaft. does the shift collar line up with the shift block on either shaft? I wonder if someone just dropped this in?
Either way, it seems like I might be pulling his unit now. Unless the rollers fixes my issue.

Input shaft spline or keyed
Utility Vehicles UTV/ATV
Replies 20 Post by Coachlarry

please reply or message me if you happen to have one.

WTB Secondary clutch for Gator 6x4
Utility Vehicles UTV/ATV
Replies 1 Post by pcweber