Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

I am not blind to the county of origin meaning will not auto buy say USA label but will give some preference to it. One label we are very strong on is where seafood comes from, no Asian due to its history of disease. If all were to me the same would pay a little more for Canada or USA label over any other. Especially if something you may need parts for.

As to the mowers at JD store of the JD at Home Depot no idea how they may compare or not but it is not just is the engine the same how about the deck and such. Might be, not my style of mower and not throwing off just we mow too much for those mowers.

Then in my profession I am an insurance agent and do sell with a USA company owned by USA Chinese now and also some with Canadian owned companies but do not with any company out side of US or Canadian owned for I have no idea how well some of those countries regulate a company and insurance is normally a long term product.

North American Power Tools
Shop Tools
Replies 12 Post by kthompson

Hi<br>
my tractors 3pt lift is leaking down. I read gregs thread and I have done this before when i 1st bought the tractor, but am having trouble remembering how to reseal the piston. I have it open from the back and can see the the connection. I think I need to pull the pin out and hold up the arms then?? Do I need to open anything else under the seat? Any diagrams?<br>
<br>
Thanks in advance<br>
Gary Sherman 602-410-5577 feel free to text if you post or want to talk

2005 Jinmafarm pro 3 point piston rebuild
Jinma Farmpro Agracat Nortrac
Replies 1 Post by azsuns

Thanks for the reply. I know prices will be higher now but still desire a front blower.

What kind is best for the price roughly one that can be fitted to a Kioti KL 3054 26HP?

I would imagine much modification to the tractor should be made.

Rear-Pull Snowblower
Snowblowers / Snow Plows
Replies 14 Post by Budspwr

There is a guy who has added rubber paddles cut from a used snowblower paddle to close the gap between the impeller blades and the housing. Search youtube for 'Make Wood Chipper Throw 2x as far and never clog' and see how much better it works.

I also have experienced problems with Jima clogging when I am running a lot of small branches with leaves and may go this route.

jamming chipper 6 jinma
Operating and Attachments
Replies 12 Post by dzimbric

[QUOTE=4kubota;77935] Thanks Kwschumm that is the kind of info I am looking for. I've read all your info and seen your pictures nice outfitt. I have 20 acres of woods and am always cutting and cleaning. I can burn with no problems but I am not a wasteful person if ya know what I mean. I have mostly pines and oaks. The nearest I've found the Jinma chipper is in S.Indiana $1500 about 11hr drive. No one around NW Florida sells them.If anyone knows closer source let me know. Please post when you have yours chipping. [/QUOTE]
I purchased mine in NC, it's not a Jinna but very similar for $1600.00. I have worked it a lot and it has more than paid for itself if I had to rent one.

PTO woodchippers again
Operating and Attachments
Replies 43 Post by dzimbric

I have a PTO driven WC8 Wood Chipper manufactured in China that will turn 4 inch logs with branches into wood mulch as fast I can load branches.
The issues I have had to date were having to re-engineer a couple parts on my shaft driven roller feed such as adding a set screw to the hub to keep it from falling of the roller when handling bigger branches,
The discharge will clog and stall the tractor if you run a lot of little branches with green leaves. If you chipping 4 inch branches the wood chips should keep the discharge clean and it only takes a couple minutes to remove the discharge tube and clear the clog.
If you search alibaba.com you can order one for a very reasonable price. I have 12 acres we are clearing of hardwoods and this machine has paid for itself.

Fresh branches with leaves chipper type
Operating and Attachments
Replies 20 Post by dzimbric

I'd have to go along with murf's line of thinking. That's why I asked if you tried both speeds. My lever shifts easily into the 540 speed, but I have to pull really hard to get it to go into the 1000 rpm speed and even then it will jump out if I don't use a bungee to keep it up.
Sounds like you have a shift lever problem.

PTO shaft not turning
Jinma Farmpro Agracat Nortrac
Replies 17 Post by bogman

there is nothing electrical there..

PTO shaft not turning
Jinma Farmpro Agracat Nortrac
Replies 3 Post by rcampb10

I haven't replaced the belt and clutch needs work, gears grind going into forward or reverse unless I drop RPMs down by pulling choke lever. We enjoy the ride, just have to watch out for moose.

Gator Speed Engine Temp
Utility Vehicles UTV/ATV
Replies 6 Post by 6x4gator

Hi,<br>
My D1600 is putting out 14.7 + voltage consistently, is there a way to bench test the voltage regulator? It is a 6 wire external model.

D1600 voltage regulator
Mitsubishi
Replies 2 Post by bigcrunch

Your message leaves a lot to wonder about: are you selling it or looking to buy or what?

Steiner Rough cut 66 mower
Articulated Tractors
Replies 2 Post by kthompson

Many thanks to all of you for your advice! :) Here's my plan:
1. Start tractor, let run for 15-20 minutes without using hyd. functions and feel for warm/hot components.
2. Run the tractor with bush hog until the problem occurs, then turn-off PTO and see if hydraulic function returns. Try shifting between Hi/Lo on transmission lever and see if hydraulic function changes.
3. Drain the hydraulic oil and remove filters, suction screen and filter relief valve. Clean suction screen and make sure relief valve can fully close. Reinstall valve and install new filters.
4. Replace the 3-pt. load shaft seals. Should I use standard JD replacement seals or is there a better after-market design available? Any special tools needed? How much shaft wear at the seals is acceptable?

Unfortunately, I may be a month or two before I get to this as I'm recovering from back surgery, but I will let you know how it works out. In the meantime, please let me know if anything else comes to mind.

Hydraulic Problem - John Deere 2750
John Deere Tractors
Replies 10 Post by KevinsJD

Hand not thought of that, guess you realize that. LOL Thank you. kt

Broke drill case
Shop Tools
Replies 3 Post by kthompson

I did some testing on this over the weekend.
I picked up a hydraulic hose, a T connector and gauge from Napa.
I first connected the gauge directly to one of the loader valve output ports to set the pressure relief to 2000 psi. I know this is 200 lbs over the manual spec but this is just a test. Then, I used the T connector with the gauge to connect it in line with the P output from the main Hydraulic block. This way I can monitor the hydro pressure from the pump while in use. When using the loader, the pressure stays around 500 lbs unless I try to lift the tractor with it or something heavy. When I use the 3-point lift, it starts around 1000 psi for a few seconds, then jumps to 2000 psi which causes the loader valve to squeal (since it's in the same loop). This is with absolutely nothing attached to the 3 point. I thought perhaps there is something wrong with the loader valve so I took it out of the loop. I disconnected the loader entirely and connected the P and N ports on the Hydro block as the manual states. I also moved the switch on the side from the "S" to the "O" position. I tested the 3-point again and it acted in the same way, 1000 psi to start, then jumps to over 2000 psi. No loader valve squeal though since it isn't connected but it was using another pressure relief bypass somewhere. It also loaded down the motor.
I thought maybe there is a mechanical bind somewhere in the lift arms but I can lift it myself with no effort.
Do I have a bad 3-point lift control valve?
Bad hydraulic cylinder?
Clogged up line or something?

Front End Loader relief valve squeals when 3 point is used
Cub Cadet
Replies 11 Post by jfortune06

You're welcome. You lucked out, eh? Here's a little more reference material I dug out that you or others might find useful some day:

--------------------------------------------------

John Deere BM20701 Dump Cylinder Notes
======================================

Originally manufactered by Warner Electric, P/N D12-21B5-05JD. Manufacturing rights are now held by Thompson Division of Danaher Motion.

Specifications:
Proprietary John Deere product
Referred to as a "B-actuator"
12.89" CPCD
5" stroke
1,500 lb. capacity
R0705 square nut drive
172 standard 0.125" ball bearings
Split return tube P/N 906-9070 (2 required)

--------------------------------------------------

On the one that I rebuilt, the return tubes had worn to the point that the ball bearings spilled out into the actuator body. It was a learning experience...

2003 4x2 gator lift bed
Utility Vehicles UTV/ATV
Replies 10 Post by JLMiller

Don't know if you found the tire you were looking for but you can try here,

http://www.surpluscenter.com

they have lots of stuff and it is changing regularly.

5100 front tires
Parts and Repair
Replies 2 Post by handyeman

That link didn't work for me spyder..maybe too old. I got my TM1518 here - http://manualexpert.com/john-deere-tm1518-technical-manual-for-gator-4x2-6x4-utility-vehicles

TM - 1518 for John Deere Gator
Utility Vehicles UTV/ATV
Replies 3 Post by starwinger

I assume you meant you bled the system by using the bleed screw that's on the injector pump?

Now it sounds like it's time to check the injector pump solenoid. It's on the rear (rear = towards the back of the tractor; on the left as you face the right side of the tractor) of the injector pump and should have probably 2 wires connected to it.

If the solenoid doesn't pull in when you turn the key to Start and stay pulled in when it's in Run, you'll never get the tractor to run as the function of the solenoid is to turn the engine off by cutting the fuel flow to the injectors.

No fuel to injectors
Cub Cadet
Replies 27 Post by chashm

Willie you tell bad news very well! I think there must be the truth or a very well established line the system needs to be pumped about ever 3 to 5 for they say the same here. kt

Septic tank care
Home Improvement
Replies 5 Post by kthompson

That sounds like a good employer. No doubt you are a good employee. You know this but bears reminding you, walk anywhere you will be tilling the first time. Look for metal post driven in the ground, large rocks if you have them there and so forth. Also nails or such for damage to the tires.

Another question
Shibaura
Replies 6 Post by kthompson