Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Sorry, you can tell my old jubilee is gas. My 404 is diesel. I should have said injector.

06 Foton 404 fuel shutoff trouble
Other Tractor Brands
Replies 5 Post by yocsr1

I have a Mitsubishi mt372 that i can't get started. I have owned the tractor for four years. I was mowing the other day and it felt as though i was running out of fuel. I shut it down and returned the next day filled it up with diesel and tried to finish mowing. It started right up and ran just fine for another 45 minutes until it started to feel as though it was running out of fuel again. Knowing that it wasn't, i didn't shut it down but let it continue to run. While doing this it would idle up and down on its own and continued to do so for about 2 minutes until it finally died. I removed the fuel bowl and cleaned it, replaced the fuel filter, charged the battery, bled the entire fuel system, and checked the air filter. The engine turns over with enough rpm to start, I've had it long enough to know what it takes to start it, but only puffs black smoke. I did get it to run off of gas fumes but that's the only way it will run. Hopefully someone can give me an idea of something I'm not thinking of or tell me to just cut my losses. Thank you

Mitsubishi MT372 does not start
Mitsubishi
Replies 12 Post by ackley

On a Foton 404 trying to remove shaft from trans housing looking for info on how to do it if anyone has,not enough room to get it out

Foton 404 How to remove Primary trans shaft
Jinma Farmpro Agracat Nortrac
Replies 1 Post by bigcalvin66

I get you. Your talking a lot bigger than I was thinking. I'm like you, the dealers should have the info. You might get online and get tx for Baine & Co. and see if they can tell you anything or atleast point you in the right direction.

Sprayer GPM controls
Parts and Repair
Replies 5 Post by yocsr1

Ah that brings back memories to me as well. Was putting in telephone pole cut-offs for fence posts. Drilling my holes into a bank of sorts at the edge of the road. .. . otherwise flat lawn. The auger caught hold down under, and down she went! As you pointed out kt, faster than the clutch could be thought of. Tried with a bar to reverse the auger...no luck. Disconnected the digger from the tractor and there she sat. LOL
A neighbor stopped by with his orange, and we tried to lift the bugger out...no luck. We then REALLY showed the town folk how it was done, as the two of us muscled the darn thing around in circles to reverse the direction. Eventually we got her out and reattached, but not without A LOT of sweat, certain embarassment, and A LOT of laughs! Now if I want a hole for a post, I'll dig with my backhoe and backfill! LOL
Best
Willie H

B2620 implement arms won t move
Kubota Tractors
Replies 23 Post by WillieH

WillieH has posted a new photo.

Subject: Kubota Generic Hydraulic Lift Drawing.

Description: <br>Hydraulic Lift Arm

Kubota Generic Hydraulic Lift Drawing - New Pix by WillieH
Photos
Replies 1 Post by WillieH

Dennis that is not what I thought you were talking about. I thought you were talking about for an open hose with not end fitting, sorry.

I would say your pricing on those is fair. Now what size are mine? Until recently had no need for the color fittings or did not realize I did until it hit me sure would help on hooking up rear remotes so you do not hook the hoses backwards which still works but, well works backwards.

Compact Tractor Hydraulic Dust Caps and Plugs
Kubota Tractors
Replies 4 Post by kthompson

Hello something is wrong with the 4x4 on my 204c it does not go into 4WD.<br>
<br>
I took the plate off in front of the gear shift and as I engage the 4x4 lever I can see something moving down in the casing. The drive shaft moves as the tractor goes forward and reverse, but the front end will not engage. <br>
<br>
As I engage the 4WD lever it seems easier than normal,I still push in the clutch and let it out slowly and as the tractor starts to move is when it used to go into 4x4, but not now, any ideas what to do next? <br>
<br>
Thank you !

Nortrac 204c does not go into 4WD
Jinma Farmpro Agracat Nortrac
Replies 1 Post by cdjordan

How did you determine it was going into the engine? The hyd oil lever is dropping and the engine oil raising? I would find it hard to tell there is hyd oil in the engine oil I think.

NT75 Hydraulic oil getting into motor oil
New Holland Tractors
Replies 3 Post by kthompson

� Battery has low voltage.

� Loose or corroded battery connections.

� Fusible link is melted.

� Spark plug wire is loose or disconnected.

� Faulty spark plug or coil.

� Fuel shut-off valve turned off (if equipped).

� No fuel or improper fuel.

� Plugged fuel filter.

� Defective starter solenoid.

� Open-circuit in wiring.

Turf Gator Starter
Utility Vehicles UTV/ATV
Replies 2 Post by PaulChristenson

[QUOTE=cowrider;193184] here are some links for a 250AS which uses a 2 cylinder instead of your 4 but it will give you an idea. Specs should be the same. Try posting the ques ... [/QUOTE]thanks for the help I really appreciate it!

belarus 400an torque spec for rod and main bearing caps
Belarus
Replies 4 Post by riverrat

Its easy and you may want to order a replacement too. Its on the Right side of the tractor in the back of the pump housing. One bolt holds the end cap on holding in the filter. Mine was really full of gunk and cleaned it and it started working again but since putting an new one in its great!

Shibaura SD2243 4x4 Tractor Advice and Manual
Shibaura
Replies 14 Post by jethead69

jadezhang has posted a new photo.

Subject: Jinma tractor.

Description: <br>the biggest Jinma tractor distributor, 16-50Hp jinma tractor with CE and Jinma254 284 with EPA. jinma tracor spare parts

Jinma tractor - New Pix by jadezhang
Photos
Replies 1 Post by jadezhang

Went under the tractor today. I just could not get the Hood to stay down thought it was me. the stub from the food that is supposed to catch in the latch is about a 1/4 inch to short. Once I unlatched it to change the oil is has never went back down. Using a Bungee cord for now but I gotta call the warrant-tee folks now.
Only Issue so far. Less than a month owning it hoping its the only Issue

NorTrac 35XL Northern Tools Foton I think
Other Tractor Brands
Replies 17 Post by Gameman

http://www.shredderhotline.com/hotlinestore/store_po.htm

Duerr hp 678 Chipper replacement blades
Operating and Attachments
Replies 86 Post by akrock

I have sold my tractor for $15,000, including the brush hog.
Thanks for your interest.

2005 Kubota B3030 tractor w130 hours
Kubota Tractors
Replies 4 Post by mrbobpb3030

Alright

I traced the electrical to those 4 wires on a terminal and started to look at the fuel pump.

I look more closely at the fuel pump and noticed when I tightened it down, I had hooked some wires and crimped them to the frame.

Looks like it was cross powering due to me not being careful enough.

Thanks for all the responses.

MIke

John Deere Gator Electrical Wiring
Utility Vehicles UTV/ATV
Replies 7 Post by orchardgator

Well, some general troubleshooting.
If you pick up on the arms, do they push down?
If so then the depth control may be on.
did something bump the arms up then they crashed down hard?
The I would suspect the arm or rod that goes to the piston may have punched through or cracked the piston (happened on a ford 8n I fixed.) Would have to take it apart to see.
If you lift, does it lift smoothly? If jumpy, could be that your pick up line has a pin hole and is sucking air.
This shows up as if the hydraulic fluid has water in it, but if you put the same fluid in a sealed jar, will turn clear and the level will drop when the air gets out of the oil.
The release control valve may be stuck open or open too much. This is the valve that slows the drop of the arms.

http://www.agcopartsbooks.com/PartsBooksN/Viewer/Default.aspx? to see a parts book. Click the link for Guest. Put in the model number You will need the serial number as there is the Massey Ferguson
245 (9A349239 AND UP) TRACTOR or before.
you can see the exploded views for the lift.

MF 245 need help with hydraulic 3 pt hitch leaking down
Massey Ferguson Tractors
Replies 4 Post by arcwelder

I bought a new JD4210 in July 2002. The reverse in the transmission was always stubborn and gradually got worse. It would pop out on its own and required manually holding the shift lever to keep it in reverse. It got so bad that I was afraid to get into a corner where I would need reverse to get out of it which limited where I could use the tractor, which I mainly used for pasture mowing. I had a loud noise develop and when they took the transmission apart the bearing for the drive shaft had disintegrated and had to be replaced. When I first got it back the transmission seemed to work better than ever, but then suddenly it became almost impossible to get the shifter out of the gear it was in, making it near impossible to restart the engine once turned off since it has to be in neutral to activate the starter. It has been returned to the dealership for repairs again, and I have heard some discussion that the 4210 transmissions have perhaps been having significant problems from other buyers too, but I don't seem to be finding the correct website forum to uncover information about this and what responsibility the John Deere company may be taking or be required to assume for the cost of labor and materials for making such a repair. Anyone else out there know about a website where I might learn more about if this is a wide spread problem and what the company has been providing in terms of corrective treatment and expense coverage for others with similar problems? Perhaps my information about this being a common problem for standard transmission 4210's is not correct? thanks, Mike

JD 4210 TRANSMISSION
John Deere Tractors
Replies 4 Post by mikerowland

Could be the governor kicking the throttle up to compensate for the engine slowing because of hitting a difficult section (thick grass, or too tall).

Or a slipping belt or clutch due to thick grass resulting in slippage and engine speed increase...

Garden Tractor speeds up while Mowing
Garden Tractors
Replies 5 Post by ford2000