Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

The quick connect coupler on the valve block already on the tractor...

Ford 1700 Loader Control Adapter
Antique Tractors
Replies 5 Post by swizcore

Steve: Since the injector pump output is very small you need to remove the input pipe to #1 injector, loosen it at the pump input and temporarily add 3-4" of rubber hose to the open end. Now wire it up temporarily so that it is vertical and level at the top. Fill the hose with clean diesel fuel and turn the engine over slowly while watching the fluid that is level with the top of the hose. Due to surface tension, you will see the fluid level begin rise above the hose when the injector begins o fire. Its a small movement but this will give very accurate results. Call a good dealer for injector timing for your engine. There are several differences in Y485 configuration that may cause timing to be changed a degree or two. Good Luck!

Monty

Y485 Injection Timing
Jinma Farmpro Agracat Nortrac
Replies 8 Post by MontyJones

The socket size needed for blade change is 1 1/2". 3/4" drive will make it easy to break loose the nuts. You will probably need a 6 or 8 inch extension to reach down through the deck.

John Deere MX6 Brush hog How to change blades
John Deere Tractors
Replies 4 Post by jdgreen

Do you still have the backhoe ? I am interested...//Thx...///Terry 301-933-5277

[QUOTE=Bill;10642] I have an 8B Backhoe for sale right now. It is attached to my 870 JD tractor. This is my second one of these. They are very good hoes. I have had no problems beyond popping a hydraulic line once in a while. I went from a smaller version that I had on a 750 JD several years ago. You will be surprised how much work these hoes can do. My 870 with the hoe is for sale right now but I would sell the hoe seperate if you are interested. It is a 1996 year.Regards,Bill [/QUOTE]

backhoe for JD 1070
Other Tractor Brands
Replies 11 Post by mysteryman

I have a Mitsubishi 3201diesel, 2 wheel drive tractor. I need to know where the oil drain plug is located & where I can find an owner/operators manual.

Mitsubishi 3201 Tractor owners manual
Mitsubishi
Replies 2 Post by hornedfrog63

got a 1975 case 480B Const King with G188D engine. Roosa master injector pump. used it about several weeks ago and ran fine. parked and waited several weeks then went to use it again..only starts on starting fluid. manual shutoff is working and fuel to pump. pulled the little side plate off where you time it to see if the shaft was turning and when i did had about a cup of diesel come out. couldn't find my mirror to check to see if the pump was turning yet. Is this normal or a possible bad pump? <br>
<br>
Thanks for the input...

Case 480B Construction King does not run
Case
Replies 1 Post by gdiffee

If the high pressure functions all quit at the same time, I would check the hydraulic pump coupler to be sure it is still turning the pump shaft. The splines can strip out and pump is no longer turning. If pump is turning, then you need to be sure oil is being delivered to the front pump. try removing the hose at the oil cooler coming from the top of the pump. Stick the hose in a bucket and start the tractor. You should get at least a gallon and a half in 30 seconds. If no oil is coming from the transmission, you wikk have no hydraulics. If you do have oil, then the main pump is bad. Could be a bad stroke control valve.

John Deere 2940 Tractor Loader does not Lift
John Deere Tractors
Replies 2 Post by jdgreen

Gameman,

Interesting read. Hope it works well for you and the one suggestion I well say to make it last well is to really "like it". Ever notice a person who took a car that the previous owner said was worn out and it ran and ran and no problems for they "LIKED IT" and thus were not picking it to death.

On real side, do keep up with service. From experience doubt you will find tougher job for a farm tractor than working with clearing land. I have done my share but they are just not built for it. So you must be extra careful. A farm tractor is not built for hitting any much more than a corn stalk and any way you take it a 3 inch limb is much harder and tougher. Again you can do it just keep your eyes open and move slowly and you should be fine. God Bless. kt

NorTrac 35XL Northern Tools Foton I think
Other Tractor Brands
Replies 17 Post by kthompson

812keepr,
The more you tell about the 812 the more I realize the 601 was a very basic tractor. We have a pond and ditches here and with the 601 working with cutter there was tough. You had to be ready to push it gear shift lever out of gear so the cutter would NOT push you.

Sure did not realize the 1,000 pto had been around that long. One thing think you are proving here, it pays to know your options before you buy for some of those options can really make a big difference for little additional cost when you are using a tool.

If you could post pictures it would be nice. Be safe and have fun. God Bless kt

Ford 681 Tractor 3ph will not lift
Antique Tractors
Replies 8 Post by kthompson

Went by New Holland in Chickasha this morning, talked to service manager, said it has a short in wiring somewhere. Will go through wireing tomorrow..

tc-30 warning light problem
New Holland Tractors
Replies 8 Post by garlic

There are pictures outlining your issue with the power steering slave unit.

You will only use a few of the seals, they send you enough to cover other type of units.

Go to the right side of the page and type in Huddleston, you will get a list of pictures and messages which might help you with your problems.

Nortrac 204C Tractor hydraulic and pto problem
Jinma Farmpro Agracat Nortrac
Replies 21 Post by Huddleston

Where is the hydraulic filter on a SU-1540

Shibaura SU-1540 Tractor Hydraulic filter location
Shibaura
Replies 1 Post by whtelk1

Emailme at parts at sheaftractor.net SD2243?

Shibaura SU-1540 Tractor Hydraulic fluid type
Shibaura
Replies 4 Post by lsheaffer

Should check your transmission fan!

Kubota BX2370 Tractor Vibration
Kubota Tractors
Replies 4 Post by Art White

Ken it is amazing what we see in life of a tractor. Just sold the second set of small Kubota L'series to a farmer. He is building his own front blade hook-up with hydraulic angle and lift. One get's used to push the feed into the manger area and the other is used on the other end of the cow with the manure. He runs them between 7500 and 8000 hours. So far just normal fluid and filters. We have other larger tractors going past 10,000 hours as well as even a ZD zero turn over 8,000 hours that just went to a homeowner off commercial duty.

Tractors Expected Life and Service requirements
Parts and Repair
Replies 3 Post by Art White

http://www.repairmanual.com/product/long-560-610-series-factory-service-manual-js-lo-s-560/

Torque specs for 610 long tractor - head and rod bearings
Long
Replies 4 Post by bugs46

Hey, I've always wanted a Yanmar cap to wear while out and about. This site has them at a good price. <br>
<br>
[p]http://www.four51.com/Images/Product/50a7595a511b482caed95acfc2416905.jpg[/p]<br>
<br>
http://www.four51.com/UI/Customer.aspx?p=ProductView&VariantID=HwboFkHTnvGG8tm7-sRfLCSve4Jm5wpR-p-sqA6opZTrx2d3XtaxIPeUA-e-e&ProductInteropID=&CatInteropID=YanApparel&CEI=74743979-7b4d-4e56-a0fd-707980f4dd0f&CatID=XOAy9on-sZv4owb0EvIbracBm0QW4VeUL6hQav7aaDezEPEp2WWAIoQ-e-e

Yanmar apparal
Yanmar Tractors
Replies 2 Post by bmaverick

Check your safety switches.

BX1860 PTO WON T ENGAGE
Kubota Tractors
Replies 2 Post by Art White

Found a source.

Thanks for the reply.

Closing query.

Ford 3000 Power Steering Cap Needed
Antique Tractors
Replies 4 Post by keyote

did you ever find out what was going on with your tractor A/C? Mine has done the exact same thing.

Kubota L3430 ac clicking sound
Kubota Tractors
Replies 2 Post by MoLittle