Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Handiman, I have no problem with you sharing your concerns and issues with Case, just in reality don't think you will find the support and open doors you hope to. With the police you are dealing with elected people and with private industry the stock holder is who elects them. I am very aware that the cost of lawsuits is one big part of any big business. Even for a repair shop is why so many business have liability insurance. And yes some law suits are valid.

Contacting case tractor manufacturing
Case
Replies 13 Post by kthompson

How it the tractor doing I just bought a 35XL New
Just asking

Thanks

NorTrac Tractor Quality Review
Jinma Farmpro Agracat Nortrac
Replies 58 Post by Gameman

Hi Mai Lor
How long ago did you buy your tractor.I Called the northern tools repair warranty department. They have assured me Bob that 90 days on-site repairs are covered after that I have to get it to a repair center 80 miles away but labor and parts are covered . I guess I will see how that goes. Really I hope not to have to repair it for years.

NorTrac 35XL Northern Tools Foton I think
Other Tractor Brands
Replies 17 Post by Gameman

Thanks for the update, I'll look for the manual and I'll check it out.

Belarus 520 Tractor Leaking from bellhousing
Belarus
Replies 5 Post by Stevarus520

Again, thanks !! Will try, too hot to finish bushogging, whew...

Kubota L275 finishing mower needed
Mowers Field and Finish
Replies 5 Post by Sallyd

I think you have had some sharp minds trying to help you and here is one old one chiming in also. Have not had a small Honda gas engine so no idea how the choke system on it works, but by chance does it have like a two stage choke? By that I mean a full choke for when first cranking the engine and then partly open choke for the first few seconds of run when you do get it running? If so that may be your problem. I have Stihl and Husky engines with this set up and if you were to leave them on full choke they would run like you are talking about.
Then one other thought as this is pressure washer I understand, does the water pump side have a switch to detect if no water flow to cut the engine off to save the pump?
Also it would fit what you had to happen with running out of gas and refill and then this problem with new gas: are you sure it is really gas? Not being smart but I had about same issue and somehow there was diesel fuel in mine gas. The other thought that comes to my mind is there was a piece of trash in the new gas and it is takes about 15 seconds for it to be sucked in place to cut off the fuel on the outlet.

Honda Gx270 Will not start Stumped
Shop Tools
Replies 13 Post by kthompson

If it's an electric tach, then you might have your wires crossed or polarity backwards. If it's mechanical then....your engine is running backwards? Not likely...stumped if its a mechanical tach.

Case 580E Tachometer Runs backwards
Case
Replies 2 Post by bloggins

Reminds me of bucket pin on my mini Volvo. Pin broke and was able to drive out the broken pin but the damaged bushings had to be ground out with carbide bits. Were suppose to be able to drive them out also.
Only thing I can say is very fine steel surfaces that are joined for a while to another fine steel surface they seem to join. Not sure what it is called but it almost seems like the steel is a living item.

Then having worked for major heavy equipment manufacture for a few years it could be the pin was really over size or the bushings undersize of they did not line up as they should have and as we said "if it does not fit, get a bigger hammer" and I honestly saw some shafts there was no way to remove once they were driven in. When we saw such it was normally due to the two bushings not being in perfect alignment but they really do not want any slack in the none rotating part of the shafts either.

Case 580E Stabilzer pin removal
Case
Replies 2 Post by kthompson

I am assuming it is suppose to cut off when you raised off the seat. It sounds like you have a safety switch issue. You may have a control that is not fully in neutral or somehow it has gotten bumped and not lined up as it should be.

Do all your steps to crank it and with key held to crank work each lever or safety switch slowly to see if a slight wiggle finds the issue.

John Deere 1070 wont start
John Deere Tractors
Replies 2 Post by kthompson

hope the leak is resolved and didn't ruin the manual....might be something else in it i will need.... thanks for the confirmation.

E184 Diesel-Kiki injector pump removal
Hinomoto
Replies 3 Post by cansox12

Did you get your tractor fixed?

I have the exact same problem.

Mitsubishi MT1601D Tractor clutch doesn t engage
Mitsubishi
Replies 10 Post by OR_MT160D

Here is your Operator's Manual http://manuals.deere.com/cceomview/OMLVU19619_E9/Output/Index.html?tM=FR

John deere 4720 Tractor Hydraulic Trouble
John Deere Tractors
Replies 7 Post by PaulChristenson

I would love to hear more about the swap you did. Please shoot me an email rudyrreyna***hotmail***.com I may be intrested in doing this swap or buying the engine you removed. or heck give me a call214 6686 9540

Ford 1000
Antique Tractors
Replies 10 Post by rreyna

I use to work for a large (at least then) heavy equipment manufacturer and we used a lot of hydraulic cylinders. It has been about 30 years and a lot has changed but does Case make their cylinders? Since they have been bought have they changed their cylinders to what is on New Holland. I have been told and no way do I know if true or not, now only the color is different now between the two.

Case tractor bad engineering designs
Case
Replies 9 Post by kthompson

My guess is you are looking at a common design at least "here". "Here" is important for I think a lot of that type of metal is formed somewhat locally from roll much like they do gutters now as they will make it to the length you want. I know on my barn the metal came from two different sources but I bought from same dealer and they matched perfectly.

Help Identifying Metal Siding
Barns Pole Barns
Replies 3 Post by kthompson

Found this link and info about them. If this does not work then try to find out who built that model and hope it is brand with parts available.

http://tractors.wikia.com/wiki/Task_Master

Taskmaster Trooper 426e 4x4 - need parts
Jinma Farmpro Agracat Nortrac
Replies 4 Post by kthompson

The tractor was manufactured for Rhino by Jinma in the late 80's/90's - it does exist!

Jinma 754
Jinma Farmpro Agracat Nortrac
Replies 6 Post by saglejeff

The diesel engine is Lijia from Fujian province.If you want the spare parts, please contact us. Though I don't know the brand of the tractor, i am sure it's not the Jinma tractor,cause we are supplier of Jinma tractor parts.

What Make Chinese tractor 40HP SL3105B engine
Jinma Farmpro Agracat Nortrac
Replies 12 Post by jadezhang

Thanks. Will do that.

Dave...

Cenex manual
Other Tractor Brands
Replies 3 Post by dpuhl2329

If you have been rotating the pump around more than one revolution, you probably have the timing off now.
you will need to set the timing for the pump again from scratch.

How do I get out the fuel pump on jinma 224
Jinma Farmpro Agracat Nortrac
Replies 11 Post by arcwelder