Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Search Belarus here. There have been a good bit of threads on them.

505M 3 point controls
Belarus
Replies 4 Post by kthompson

Davedig, no idea on your tractor but had a coworker to have his arm "TORN" off with a hyd steering system connected wrong. Rather than the steering valve operating as a control valve it was connected to operated as hyd motor and it did. He had his arm through the steering wheel as the engine was first fired on an assembly line and it fired up with full pressure turning that wheel at a high rpm. kt

B1750 steers itself all the way to the left
Kubota Tractors
Replies 3 Post by kthompson

vanfleet1, if you are referring to trimming around trees okay but I read your reply to mean trees themselves being trimmed. Do not think a trimmer on wheels would be reasonable to trim limbs on any type of trees I have ever seen. Well maybe weeping willows. LOL

Trimmer on wheels
Garden and Landscape
Replies 8 Post by kthompson

Treeman, I used a cutter once without the top link and regretted it. A friend suggested leaving it off for the cutter to follow the ground better and it did, as it pushed the pto shaft into the rear end jamming a gear in the transmission/rear end. I did that backing up a slope. The only good part was it jammed the front pto which I do not used so was fortunate there.

KingKutter 6ft Brushhog
Mowers Field and Finish
Replies 7 Post by kthompson

One point to the turkey fryer, hyd oil will burn. Maybe easier than you think. To the point I use old hyd oil to burn stumps and such. I have no idea what that flash point is for it but if you have used any kerosene or diesel fuel to flush the system and it is in your hyd oil,,,well just be very careful.

water in hydraulic fluid
Long
Replies 10 Post by kthompson

Hi,<br>
<br>
My left front bearing went out on my 7275. I took the wheel off. The housing is shot. I have the shop book, doesn't show good pictures or give a lot of information. It looks like I have to pull the gear off to get to the oil seal. Is there somewhere I can buy a used unit/housing complete or do I have to rebuild it. Where is the best place to buy the parts?

Front axle repairv- need information and help
Cub Cadet
Replies 2 Post by cub7275

From bitter experience, I can confirm that a simple thing like the radiator cap can cause some confusing overheating issues!

Gator 6x4 Overheating problem
Utility Vehicles UTV/ATV
Replies 13 Post by spyder

I have a Massy ferguson 1010 diesel tractor and would like to see if anybody knows where I would hookup the lines for an extra hydraulic valve on my tractor for a front end loader. It is Hydrostatic drive.

extra hydraulic valve
Massey Ferguson Tractors
Replies 2 Post by LoneWolf216d

Some makes seem to have few issues and some have a lot of issues depending on care. Sounds like jd prices but that price probably included labor. Some dash boards are only in the 200 dollar range.

Fuel and Temp gauges
Kioti Tractors
Replies 3 Post by Art White

Greg gave good advice. I try to wipe my quick connectors every time before I hook them just in case there is a speck of dirt to hold the valve open. No idea on a fel loader but you may find you need to release pressure on the hyd system to disconnect or connect those fittings. Depending you on your system that may mean cutting the tractor off and working the controls. kt

Foton 404 fel removal
Jinma Farmpro Agracat Nortrac
Replies 4 Post by kthompson

I think your tractor has wet brakes, meaning the brakes are running in the hyd oil system. If so them sticking I would think would be the linkage outside the rear end. Begin by checking that linkage for heavy rust or bends or some foreign material such as a piece of limb even.
Check the hyd oil level. One other thing, does your brakes had a lever to lock them engaged? Look and be sure it is not getting locked. Could be issue with that also.

But you either have stuck brakes or no breaks? That seems rather odd to me. What kind of transmission do you have, manual or hydro-stat? If hydro-stat often you don't use brakes as much and might be easier to miss them going bad or how they really are working. Does this happen with both brakes or just one side? Are the brakes locked so both work together? Normally a flip lever on the pedals. kt

massey ferguson rear brakes sticking
Massey Ferguson Tractors
Replies 2 Post by kthompson

Just wondering, how did your seal repair go?

MF 471 PTO Seal
Massey Ferguson Tractors
Replies 2 Post by kthompson

Is this air conditioning in your house or other building or on a piece of equipment? How do you know it is using "much more energy"?
What have you done to check or service it? If it has filters have those been changed?
Is the weather hotter than normal where you are?

Unless you know A/C systems and have the equipment the recommendation for professions is proper. A small screwup can increase repair cost.

Air condition is consuming more energy
Home Improvement
Replies 3 Post by kthompson

[QUOTE=gtorose;142714] Did you ever get a manual for your D10? I bought a new copy from my local CAT/Komastu dealer. The local dealer here was able to get all my replacement parts I needed too. [/QUOTE]

I know this post is old. But I was wondering if you would give me the name of your local CAT/Komatsu dealer. I need manuals and my local dealer refuses to order anything related to gray-market units. thanks

Komatsu D10S-1 loader backhoe crawler
Other Tractor Brands
Replies 4 Post by guan-xi

Thanks I will give them a try

Frank

12V conversion
Antique Tractors
Replies 3 Post by stonewall

Dennis,

Yes, our snow has melted, but the rain doesn't seem to stop. We've visited the tree pile twice over the past two weeks. The mud is at least ankle deep around what remains of those trees. It appears as though it may be August before we'll be able to get in there without getting stuck.

I'll keep you posted.

Joel

Tractor Forestry Skidding Winches
Operating and Attachments
Replies 31 Post by candoarms

I remember back in the late 70's early 80's we were the northeast distributer for Same tractors. It seemed that while coming across in the early days that the salt air would get into the clutch housing and rust up the shafts. Although I can only remember having to split a couple in our shop normally a high gear run and hitting the brakes would jar them loose.
It does sound like yours is a bad one and I'd recommend splitting so your costs might be lower possibly not having worn out the clutch disc yet.

TC45D Clutch Shuttle Shift - Won t move
New Holland Tractors
Replies 2 Post by Art White

[QUOTE=edwardleh;190579] My tractor has a front end loader on it. The pipe on the left side of the housing goes forward and I belive it feeds the front end loader valve. Can this feed both front end loader and the 3 point hitch at the same time? [/QUOTE]No way to tell from your description. Have to look at the way the hydraulics are plumbed. Can you post photos?

//greg//

3 point hitch hydraulic system
Jinma Farmpro Agracat Nortrac
Replies 8 Post by greg_g

Which 420 do you have? Is it a lawn and garden tractor from the 80's or a two cylinder utility tractor from the late 50's?

JD 420 Tractor wont start up
John Deere Tractors
Replies 3 Post by jdgreen

You are correct. THe short, short, short, long code is for the throttle position sensor voltage out of range. When this code is active, that load match is disabled and that is why your symptoms go away. A thought just occurred to me.. Maybe you should check all of your engine mounting hardware. If the side frame bolts or bell housing bolts are loose, it might allow enough flexing of engine in the frame while turning to cause the flywheel sensor to malfunction. If bolts are all tight, I would replace the engine speed sensor, or at least swap the mfwd sensor and flywheel sensor to see if anything changes.

4310 Load Match Jerking while driving
John Deere Tractors
Replies 12 Post by jdgreen