Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

I've always found that buying something used or old is just as much fun as buying new. You might want another model someday but you can deal with that later. This one should do alot of work for you.

Have fun.
Dave

B 7100 ST - Making the Leap
Kubota Tractors
Replies 57 Post by shortmagnum

Don't get me started on milk they sell at the store; some numbskull decided that all milk sold in the US must be pasteurized and homogenized and now we end up drinking something that resembling diluted latex paint. If they made it a choice for the folks to drink pasteurized and homogenized milk, that would be fine, but now you can't even find a farm (and we live close to the dairy country in PA) that would be willing to sell you the milk before they pasteurize it, because they'll get in trouble if they do that.

mowing with a brush hog
Kubota Tractors
Replies 41 Post by DenisS

I used a Cyberdyne 2X4702650 Gauge. and ZX470271B Sender from JC Whitney. Around $55.00 It's still working after almost 2 years.

Enclosure for 2210
John Deere Tractors
Replies 20 Post by busguy

The forks I use on my neighbors tractor (5000 series is quick attach) from the loader and suspect the ones for the 4000 series are similar, just pull the pin at the bottom and switch. The cost will eat up most of $1,000, closer to $900 when you include taxes.

4000 Ten Series Fork lift impliment
John Deere Tractors
Replies 13 Post by jd2210

BX23-24 would give you the backhoe and allow you to mow both applications.

Kubota L 2850D Replacement
Kubota Tractors
Replies 5 Post by Art White

Greg, are you sure your glow plugs are working, 5 sec should be enough time to start, also you may have to give more throttle,if you have checked your glow plugs then the timer may be next, can you by pass the timer to see if the glow plugs will lite for 5 sec ? paul.

6284D starting hard any ideas
Cub Cadet
Replies 9 Post by tarbaby

Filter used in Japan for assy. Is not available here. To cost prohibitive. Both filter have the same filtration properties mainly just a different seal is use by the manufacturer of the stocked filter you get from the dealer. Which is why you did not have the problem prior to your service.

FEL - jerky movement
New Holland Tractors
Replies 13 Post by oneace

The gauge designation applies to all but the .410 bore shotgun which is measured in inches. One of my favorite size shotguns.

shotgun gauge trivia
Just For Fun Off Topic
Replies 9 Post by Chief

There are scads of them avaiable from tractor supply, international dealer, or antique parts suppliers.

Do a search for Farmall H on e-bay will give you lots. If you need more I'll have to get you some links from my PC at home.

carb for Farmall super H
Antique Tractors
Replies 2 Post by harvey

Hello everyone. I just found this site and I feel very fortunate. You all have a lot of great experience and input.<br>
I hope you might be able to guide me in the right direction. I am looking to disk about 2 acres of land with my 1510 (so I can do some seeding) and I am trying to find a good quality disc at a reasonable price. Do you have any ideas on a make/model?<br>
Thank you for your time.<br>

Disc for a Ford 1510
Shibaura
Replies 1 Post by Sandman

Great! Thank you all for the quick response. I really appreciate it.

1510 3 point hitch question
Shibaura
Replies 4 Post by Paul

The engine was rebuilt by a very good Mech. I think the big problem is that I am in NY and dealer is in NC, 900 miles between those letters!
I bought the tractor used and did not have it very long before it started to make a very ugly noise. I was covered under warranty and never really got an answer on exactly what happend. I do know that one of the heads hit the cyl. and all cyl. were honed.
I would like to check compression. Where can I buy, or how do I make a gig to test compression? What is best method to check?
I would also like to check the setting of the 7308 relief valve?
Thanks to all the guys who are taking the time to help me...There is alot I need to learn.

2001 TC33D 33HP ENGINE PROBLEM
Parts and Repair
Replies 11 Post by WHITEBOY11

I have a metal roof shop with concrete floor and open sheds with dirt floor all in one building. One of the side sheds will sweat as you are seeing but very little with the other two sides and the concrete floored shop it self. If you poor concrete be sure you put down a vapor barrier first.
You did not mention drainage, my shed that sweats needs grading on that side so rain will run away. The other two sides have more of a grade and little sweating.
A question for these guys with experience here, if he were to install a ceiling would that not help or prevent it? I don't think the fact whether the insulation is on the back of the roof itself or on the top of the ceiling would matter. Hopefully there would not be moisture between the ceiling and the roof, at least not sufficient to cause a problem. You may find you could use the foam plywood size sheets for a ceiling which would be light to install (no strength to them).

It s raining INSIDE my new Pole Barn
Parts and Repair
Replies 13 Post by kthompson

I agree the MX5 is a good bushhog. I've had mine for a year and a half and anything the frontend loader can push over it has cut it up! It is heavy for the 790 so you will need to mount your FEL or add weights on the frontend of your tractor. Well worth the money.

JD 790 Cutter
John Deere Tractors
Replies 3 Post by nick72126

Check out my picture 18 I have been using these chain on forks for over three years with no problems. They only cost $235.00.

A very cool web site
Operating and Attachments
Replies 10 Post by drcjv.

There is a possibility that there may be debris in the switch. You should not lose too much fluid when you remove the switch. I know on the larger tractors when the fluid is cold the switch will move very slowly to return to neutral to allow starting.

TZ24DA Transmission Range Safety Switch Problem
New Holland Tractors
Replies 12 Post by oneace

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=7568190750

TZ25DA with implements For Sale
New Holland Tractors
Replies 1 Post by tractorbuyer

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=7568190750

TZ25DA with implements For Sale
New Holland Tractors
Replies 1 Post by tractorbuyer

Not sure if anyone has experienced this, but the older 210 loader and hood guard accepts the mounting hardware directly for the quick hitch/front blade, no additional hardware needed; however, the new hood guard that comes with the 200CX or 200X loader does not accept the quick hitch directly and requires an additional component, LVB25396 to make it all work.

Front Blade Attachment for 200CX hood guards
John Deere Tractors
Replies 1 Post by jd2210

If you�re providing a mobile service you should charge at least as much as a fixed repair center. The dealer charges more for off site work, so you should also.

Remember your going to incur costs that must be paid by you or your customer. As a new business collect on the spot, and if possible before you do the work. The nicest people will screw you over money.

So you might want to look at a system where you call in a credit card, but get paid��

Tractor to dealer or not
Everything and Anything
Replies 23 Post by oldrental