Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

((if to tight and creaks when you lower or raise))<br>
<br>
No sounds what�s so ever? Shouldn�t the arms be butt up against the implement? If I make the turnbuckles looser the arms don�t rest on the on the end of the pin(against the implement). They are more towards the center? Remember my pins are mounted on the outside of the implement.

3pt sway links
Kubota Tractors
Replies 12 Post by EricBX1500

My neighbor and I are in the process of installing a joint use electric/telecom 270' ditchline with conduit. A couple of weeks ago we brought schedule 40 2" PVC for $4.30/10ft section. Yesterday, we brought the same 2" conduit to complete the telecom part and paid $8.00/10ft section.<br>
<br>
I have also heard that plywood has increased in price about 50%. I guess this is to be expected. Dave<br>
<br>

building costs
Home Improvement
Replies 32 Post by kyvette

Chuck<br>
<br>
It is a process to pull the main block out of the bottom. It is dooable. I have had mine out and switched the boom and dipper blocks around to function the same as a excavator.<br>
<br>
I spend a lot of time in the big machines and when I am in close work with the little JD hoe it was not instictive and I had to overconcentrate. Also do not just switch hoses because the blocks have different relief valves on the push/pull sides.<br>
<br>
Put a number tag on each line and make a diagram of how they go.<br>
<br>
Common tools will do the job but you will need a good quality set of open end wrenches for all the lines.<br>
<br>
I have all the rebuild parts and photos and can fax or can send you links to the JD sites.<br>
<br>
Just an after thought check all the lines first. A couple of mine were not tight but did not leak that I noticed.

Hydraulic valve repair-48 backhoe
John Deere Tractors
Replies 4 Post by harvey

The only drawback with Gorilla Glue is that it has no "gap filling" capability with any strength. It will expand to fill a gap but will not be as strong as regular yellow wood glue (Titebond, Elmers) in the same situation. The large the gap the less the holding strength of the Gorilla Glue. I use both in my carpentry hobby, like anything there is no one perfect solution. Certainly wouldn't use it where there was a chance of the foam getting on the finished surfaces.

It is a recommended adhesive in my business as a hardscaping installer (Interlocking concrete pavers, retaining walls, etc.) for wall caps, etc. due to its strength and affinity for water. I tend not to use it in these applications again due to the foaming. I use a non-foaming urethane adhesive in a tube for those applications, which is also significantly more costly that say Liquid Nails construction adhesive.

Gorillas in the Glue
Home Improvement
Replies 8 Post by kdsrgone

Mohegan,

The obvious is " the biggest you can afford", but all joking aside, you really need to look closely at where you'll use the tractor as well as any potential uses in the future. Size is a factor as you increase HP. Do you have areas where size or manuverability could be an issue? Based on your statement, you definitely need 4wd. Depending on how quickly you want to brush hog your 7 acres will determine the size of the rotary cutter you will want, which in turn will have an impact on the size of the tractor. Any uses that are not in the picture today, but have even the remotest possibility in the future should be considered. It'll be much cheaper to have some overkill for a few years than to have to go through the purchasing process again when the tractor you bought today won't handle tomorrow's work. Most manufacturers have several frame sizes in their lineup with some overlap in HP. You need to examine what your limiting factors are, then pick a few models, and arrange a test drive. Another factor to consider is ease of attachment of the various implements. 3ph rear implements are all pretty much the same, but what about the loader? Are you planning to leave it on all the time or take it on and off? If you need to take the rotary cutter or finish mower off frequently to pull wagons, you may want one of the quick-attach systems for your 3ph implements.

choosing the right tractor
New Holland Tractors
Replies 11 Post by kdsrgone

What part of the country are you in, What repairs were done?
Contact me at RonEAllen at ATT.net

Price on a B2150 with 905 hours
Kubota Tractors
Replies 5 Post by RonAllen

Thanks for the reply Gearhead. I did take the metal line off and replaced the O-rings that were in the banjo fitting but when I put it back together, it still leaked so I took it back off to make sure that the o-rings didnt fall out and they were fine.
I checked the line over real good and there are no cracks at the banjo fitting. The leak is at the bottom of the fitting that goes into the Transmission housing not at the filter head. If anyone has any suggestions as to what else I can check please advise.

Hydro leak
Kubota Tractors
Replies 3 Post by coleyslawn

Whatever else you do, don't try to wire around the problem or splice into the tail light wires. It can fry the computer functions under the hood and the dash.

2005 Ford F150 - Trailer Electrical Hook-up
Pickup Trucks and Trailers
Replies 11 Post by DRankin

Hi All,<br>
<br>
Looking for suggestions regarding the best rig for a small landscaping business. The rough critera is the smallest tractor setup (meaning turning radius/wheelbase/lenght) that can move 1500 lb pallets of rock, power a backhoe with a 7ft dig, and have options for a quick attach front bucket / forks / etc. I'm thinking along the lines of a Kioti CK30HST , but would really like something smaller if I could find it.<br>
<br>
BTW, even considered an articulated PowerTrac 1430...but not real comfortable with being locked into the limited and fairly expensive impliment options. Anyway, all suggestions and opinions welcome and appreciated.

Best compact landscaping rig
Operating and Attachments
Replies 11 Post by cmedwards

Certain greenies push the ethanol blended gasoline as a way to cut emissions as the ethanol burns cleaner. But you do get less fuel mileage so you end up burning more fuel for the same distance negating some of the clean air gain.

Some vehicles react to the ethanol blend more than others. A motorcycle is one that will react more severely than say a car will. My bike is a high performance bike so I won't even consider putting an ethanol blend into it. If you bike is a touch more on the performance end or has been tweaked, then that may account for your more severe reaction to the ethanol blend.

I'm not a scientist and I have done no technical studies to support my hypothesis.

Alcohol and gas mix
Just For Fun Off Topic
Replies 15 Post by Iowafun

Is this a new problem or has it always worked this way? Does the loader drift down if you leave it in a raised position? It sounds like you could have a restriction in a hose or steel line. Do any of the steel lines have a kink or sharp bend in it? If this is a problem that has been there since the loader has been installed, I might suspect an obstruction in a line. I have seen plastic caps left on lines when fittings are assembled cause this problem. Once I found a 3/8 nut inside a quick coupler. There are lots of possibilities, let me know if you have any more specifics to help narrow it down.

JD 790 LOADER PROBLEM
John Deere Tractors
Replies 4 Post by jdgreen

The B2710 is 20 hp PTO. You can only use a light duty 5 ft rotary cutter on that unit. The extra 5 hp means a lot. My 955 tractor is 27 PTO and I can handle a six foot in heavy grass.<br>
<br>
ncrunch I tried to plant zoysia in the centipee and the centipee chocked it out. I thought the Zoysia would be more draught resistant and provide a better looking lawn. No luck. <br>
The centipee is nice as it really requires very little mowing. It spreads so flat that the seed heads only stick up about 6 inches. Like Zoysia it goes dormant and allow the other weeds to get a head start in the spring.

choosing the right tractor
Kubota Tractors
Replies 12 Post by Peters

I think MTDs are amazingly tough for the little money you spend. I prefer more beefy and smoother riding lawn tractors but I pay more than I should for them. I grew to love lawn tractors after mowing my father's 3 acre lawn weekly when I was a kid. Took me up to 6 hours a week.

My Dad used to make the MTDs last forever but after a couple of years we had to wire them together. He'd even leave the 3 acre regular lawn and start mowing the pear orchard for fun. I know this is the best and cheapest option if you are a handyman - or if you baby your lawnmower on a nice easy lawn.

My Mom has an MTD which she refuses to get rid of because it was my Dad's and he is gone now. We just put $600 into it to replace the tranny - even though the machine only cost $900 to begin with. The nephews beat it up a bit and it failed after about 10 years. With the new tranny, and if I keep the nephews off it, it will probably last another 10 years. I would prefer a nicer riding stronger machine but this is what my Mom wanted at her house.

Lawn tractor choice help info
John Deere Tractors
Replies 20 Post by ncrunch32

If your snows are heavy and wet the 5 foot blade might push the tractor aside from the snow instead of vice-versa.

What does the dealer have against the snow plow Kubota designed for the tractor?

Snow plow blower for BX23
Kubota Tractors
Replies 24 Post by DRankin

3 thoughts on the US Government:
No one ever accused a politian of having common sense. (probably true for all countries.)
Bumper sticker: Sure you can trust the Governement, ask any Indian.
Bumper sticker: I am from the Fed. Gov. to help you.

Eminent Domain Testimony of Ms Susette Kelo
Just For Fun Off Topic
Replies 22 Post by kthompson

The 22NF is a standard BCI battery size but rare even in the normal range. It has plates that are less than 6" wide. They are a special run on any battery line. Let me do a little more hunting I thought maybe we had a solution with the even smaller AGM battery with carrying block.<br>
Maybe I will give a call to East Penn. I know they have the 22NF cases and their AGM and gell lines are rather flexible. I know a couple of friends there are antique tractor restorers. We should have a more friendly ear than Optima.

Possible Solution To The 4000 Ten Series Battery Corrosion Problem
John Deere Tractors
Replies 87 Post by Peters

Not uncommon. See http://ctoa.net/ldu/forums.php?m=posts&p=1817#1817 and http://ctoa.net/ldu/forums.php?m=posts&p=997#997<br>
<br>
//greg//

4x4
Jinma Farmpro Agracat Nortrac
Replies 3 Post by greg_g

A friend of mine is having me transfer his Myer snow plow hitch and wiring harness from his '05 to '06 2500HD. It has the snow plow prep package. What all does this prep package include? Is there anything in the package to ease installation of the wiring harness? I saw a bit of information on a GMC Web site that there is a plugged hole in the firewall to pass the harness into the cab.<br>
<br>
Craig<br>
<br>
<br>

Snow plow prep package
Pickup Trucks and Trailers
Replies 4 Post by cef2lion

I would snap it up before someone else does. I don't think you can beat that if he will take the 12K. Is it Hydro?

Re PRICE CHECK ON 04 B7800
Kubota Tractors
Replies 3 Post by Peters

I have a Shibaura SD1540B 4X4 with a 3pt in the rear that does not work.<br>
<br>
My hydraulic pump puts out a small flow of fluid, I have blown out all the lines and cleaned out the filter and still no luck. It sounds like the pump needs to be rebuilt or replaced. Is there a rebuild kit or do I have to buy a new pump and If so where do I get one.<br>
Thanx Bob

hydraulic pump
Shibaura
Replies 1 Post by triumph59y