Tractorpoint Login

print < Tractorpoint Login

Search for = kthompson

Topic

You might find NAPA has the parts for that tractor. It would surpise me if not just a seal. But something would have damaged the seal possible could be a worn bearing or age.

Super A rear wheel axel leaking oil
Antique Tractors
Replies 2 Post by kthompson

I have enjoyed reading you two on the clutch. Been very good.

2003 farm pro 2425 clutch adjustment
Jinma Farmpro Agracat Nortrac
Replies 12 Post by kthompson

Hoping some one else with jump in with your answer so am posting just to get it into the active section. There are companies who offer them at least to some degree even on line.

Free L295D
Kubota Tractors
Replies 2 Post by kthompson

Have no idea to your question but a very simple one, are you positive you are getting fuel to the pump? Assuming you were not getting fuel is the reason for the new pump.

john deere 626 fuel problem
John Deere Tractors
Replies 2 Post by kthompson

How about you used too long a pto shaft or the third arm was disconnected or adjusted too short and the implement was allowed to jam the pto shaft against the tractor? Don't forget the pto shaft needs to be measured not only at level but full up and down. I ran a mower with third arm disonnected to allow more float and ended up mowing a slope backing up, causing the mower to tilt more than normal and jamming the pto shaft together so no more slip and then into the transmission. Fortunate the damaged to my transmission was minor.

MF 1528 PTO
Massey Ferguson Tractors
Replies 5 Post by kthompson

Maybe not all but some companies show on their web site the models that fit different model tractors. Know that at least one tractor sales person felt very strongly about using only the brand as the tractor. Said they build to leave access to service points where the after market does not. As to used one have seen them on ebay. You might check Craig's list and just do a google search but there are used equipment sites also.

front loader and hydraulics
Kioti Tractors
Replies 3 Post by kthompson

I had a battery I pulled and took to two different dealerships to have tested just knowing it was bad a few months back. Both said your battery is great. It took a true battery cable tool to cut the film out of the cables that was preventing metal to metal connection so the electricity could flow.

Electrical Problem
Shibaura
Replies 4 Post by kthompson

My question might be dumb not knowing your tractor, if you are looking for fixed draw bar agree with Auerbach, if the 3 pth bar that should not be a problem with any tractor supply company.

drawbar
Belarus
Replies 4 Post by kthompson

If you are near a AgriSupply store they can be a great store to visit and get to know. Agree with Greg's thoughts there.

slip clutch brands and where to buy
Mowers Field and Finish
Replies 7 Post by kthompson

A couple of years back replaced the seat on my larger Kubota and was very pleased with the new one. Hauled off the old one to the recycling center and little later realize..where is the seat belt? It was mounted to the seat as the seat was on a suspension system. Have not come up with a good set up to use on new seat. Used the seat belt on that tractor very seldom as it stays on flat ground most of the time but still miss the belt.

Replacement seat belts
Parts and Repair
Replies 10 Post by kthompson

Don't pretend to be knowledgeable on this and don't think I know anyone with this tractor. My guess is part of what Murf is saying as long as they have been out there if there is a major design issue it would be known very well by now. At same time what brand of loader and model was used? Could there be an issue with over size loader or improper installation and thus this being the only one set up this way?

As to person being hurt, regardless the reason that is sad.

MF-471 Split in Half
Massey Ferguson Tractors
Replies 18 Post by kthompson

Just wondering here, see a lot of issues with Gators. Is that due to Gatoradier (spelling?) and others who are good about helping? Is it Gators has a high percentage of issues compare to other machines? Is it due to the high number and just normal repair percentage? Is there another reason?<br>
In my neck of the world there are by far more Gators than maybe the next two brands combined. But seldom do I notice posting on some of those brands.

Gators issues
John Deere Tractors
Replies 1 Post by kthompson

Think you will find this can vary depending on who owns the road and NC and maybe even your county laws. Not a lawyer but don't know how a person can give or take authority of who enters another persons property. Have you talked with the owner of the vacant property to find out if they are aware of the signs or not? Understand he is not the nicest person but could it help prevent problems of people being where they have no business?

POSTED SIGNS
Garden and Landscape
Replies 8 Post by kthompson

I am not sure the model gator we have but it is air cooled. The access to its engine is raise the bed. Hope that helps.

Where did they hide the coolant fill cap
Utility Vehicles UTV/ATV
Replies 3 Post by kthompson

Sorry for the experience. Did you pay with a credit or debit card? If so you may have easy recourse if you desire a refund.

If you rather keep it as you have found it you may prove to be good or not. I would wonder about any warranty based upon your limited experience. As to the replacement cutters, never need replacement makes me think they either have no expeirence selling them or expect them to be used very little. Hey we don't have rocks but stuff happens. You probably can find another brand of mower that uses cutters that will work fine on your machine.

As to what you thought of the job it does, I agree. Very much like the result of a flail cutter.

Trying to find a flail mower
Mowers Field and Finish
Replies 16 Post by kthompson

To be certain, do you like the tractor better than the 9N? LOL

Without a doubt the new tractors are much easier on the operator. Glad you are so pleased. Keep us updated on your experiences.

EX3200
Cub Cadet
Replies 5 Post by kthompson

Well you did not describe remote hyd lines. My guess is the lines are for such as back hoe. If you find the proper plug fittings you should not need a rubber washer. Metal tubing seals against another metal surface. Their is a lot of pressure there than might blow out a rubber washer. Now saying all that some fittings do have a "O" ring on them or such.

Hydraulic Fluid Shooting out back Connection point
Shibaura
Replies 6 Post by kthompson

Interesting setup there. I have never seen a tractor with the front end lift and only thought they were in Europe. How about support (parts)? I think they were bought by Agco and have no idea about parts now. No idea on the tractors but did work with a company who used their engines and the torque was low. Engine would drop rpms terrible when a load was applied. That was 25 years back so might be big difference. They were quite compared to any other brand we used.

Deutz tractors
Other Tractor Brands
Replies 2 Post by kthompson

Are you sure you have good oil pressure (checked with guage) and are using proper oil (not too thin)?

Brand new T1520 with ticking motor
New Holland Tractors
Replies 5 Post by kthompson

I do not know your transmission at all but it makes me think your shifter slipped out of the linkage in the transmission. The best I can tell you and to try and work the linkage in the transmission it self slid one at the time and try turning the wheels and see the effect. If not what you want change that back amd try again.

stuck in reverse
Mitsubishi
Replies 5 Post by kthompson