Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Feel free to keep in touch, Ed. (903) 603-9171 =)

Mitsubishi MT160 hydraulic oil fill line
Mitsubishi
Replies 8 Post by ncwtractor

I apologize that I did not get back with you sooner. (903) 603-9171 Call anytime.

front end Satoh Beaver 370
Mitsubishi
Replies 18 Post by ncwtractor

I am not allowed to advertise but my email address is sales@ncwtractorparts.net

Rebuilt cylinder head complete with valves.(valves lapped, head surfaced, new valve stem seals) Ready to go.

Mitsubishi D1600 II Diesel Cylinder Head
Mitsubishi
Replies 5 Post by ncwtractor

Parts are avaiable for your tractor at reasonable prices. sales@ncwtractorparts.net

HELP finding Shibaura tractor Parts
Shibaura
Replies 9 Post by ncwtractor

Some of those types of levers are slightly spring loaded with 3 positions. UP-NEUTRAL-DOWN. The knob controls
the speed of the implement going down. I think you might
have a worn "hydraulic" piston packing. It might explain the slow dropping of the implement. Fluid slowly bypassing
the seal packing.

If you would like to talk more, email me at sales@ncwtractorparts.net.

SU1341 hydralics will not stay in raised position wonder whats wrong
Shibaura
Replies 5 Post by ncwtractor

We supply parts for the MT25. My email is sales@ncwtractorparts.net. =)

mitsubishi mt 25 Manual and review
Mitsubishi
Replies 6 Post by ncwtractor

Email me at sales@ncwtractorparts.net for parts on Hinomoto tractors.

Hinomoto E2804 Manuals
Hinomoto
Replies 5 Post by ncwtractor

NCWTractor agrees with Murf. But, we would like to add that the IH254 was made by Mitsubishi.<br>
On those models there is an electronic solenoid that shuts off the fuel pump that is controled in link with your ignition switch and a control unit underneath the dash on the right hand side(check the side dash panel for 2 phillips head screws). You will find a control unit behind it. It will look like a voltage regulator (flat black box).<br>
<br>
Pull out your solenoid and check it. It should have 2 wires. Hook a hot lead to one and a ground lead to the other. If it clicks every time you touch it with a ground lead it is still good. Your problem could be a bad connection somewhere or a problem with your control unit.<br>
<br>
Hope this helps...<br>
<br>
<br>
<br>
<br>
<br>
Edited to remove advertising component.

254 won t start
Case
Replies 8 Post by ncwtractor

Thanks, Dean. I will be looking forward to your call. If we can be of further assistance, just let us know. <br>
<br>
<br>
<br>
<br>
Edited to remove advertising component. <br>
<br>
<br>

Need help for Mitsubishi K3A hard starting
Mitsubishi
Replies 6 Post by ncwtractor

NCW Tractor Parts, LLC has parts and technical support for Case IH1120 tractors just in case you do run into a problem or want to maintain your tractor. =)

Case IH 1120
Case
Replies 3 Post by ncwtractor

Have you checked hydraulic fluid levels? If the level is low, then you may have a bad hydraulic pump seal. The hydraulic lift valve on that tractor is a close center valve. If the 3pt lift bottoms out too many times, enough back pressure can cause the seal to blow.

Check your hydraulic fluid levels first. If you don't have a dipstick attached to your filler cap then check the side
of the transmission housing(right side sitting on tractor)
there will be a check plug midway down the side case.

If this does not help, feel free to contact us at NCW Tractor Parts, LLC.

D2350 FD
Mitsubishi
Replies 10 Post by ncwtractor

NCW Tractor Parts, LLC does not carry manuals at this time but we do offer parts for Shibauras. Visit us online today!

Shibaura SL1643D 4x4 help needed
Shibaura
Replies 3 Post by ncwtractor

NCW Tractor Parts, LLC has parts for Hinomoto tractors. Visit online at ncwtractorparts.com or give us a call at (903) 603-9171.

Hinomoto E14D
Hinomoto
Replies 4 Post by ncwtractor