Go Bottom Go Bottom

engine for ford 1710 4x4

View my Photos
sparkplug
Join Date: Jan 2004
Posts: 4 waycross,ga
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-01-12          73756

I am looking for a engine for a ford diesel 4x4 model 1710,but the local New Holland dealer pleads ignorance about any shibaura. can anyone help me with a cross reference.can anyone give me the shibaura engine number for the 1710

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
TomG
Join Date: Feb 2002
Posts: 5406 Upper Ottawa Valley
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-01-12          73766

Got to go pretty soon, so maybe more later. There have been discussions before about Shibaura Ford crossovers. You'd think I'd remember since I have 1710 but I don't know what Shibaura model if any used a similar engine to the 1710. I do know that the Ford and Shibaura engines aren't identical. It'd take somebody with a lot of experience to know if a complete Shibaura engine would be a bolt on exchange or how much modification would be required.

There was mention here awhile back that Mahindra acquired some rights to the old Ford compacts and might be a source of parts. I think that if an entire new engine is needed it's going to cost more than the tractor whether it's from NH, Shibaura or elsewhere. Maybe a parted out 1710 could be found. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
sparkplug
Join Date: Jan 2004
Posts: 4 waycross,ga
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-01-12          73780

thanks tom, I really only need a head, but everyone said that it would probable use oil if I put a new head on it with-out overhaul. Overhaul at local rebuilder would cost
1200.00 Including new pistons and rings, plus the head costing $1345.00 from local dealer.total cost to rebuild about $2600.00. That is too much for 1987 model for me to invest for home garding....I will keep searching for a used head. and install it myself...Head was pitted out so much that it did not have enough compression to start, had to pull it off every time....Going to grind out the head to remove all rust and pits and have a welder to fill back up the holes and take it to a machine shop and have the head shaved....
will advise later if it worked... ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
paulss
Join Date: Nov 2003
Posts: 60 Lavaca County, TX
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-01-12          73790

Try Eagle Tractor Parts in Eagle Lake, TX. I don't have much info on them but I seem to recall they have a website and I know they are listed in the phone book. They are not far from my ranch and have tons of old tractors and equipment . ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
TomG
Join Date: Feb 2002
Posts: 5406 Upper Ottawa Valley
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-01-13          73844

I get the pic and the oil thing likely is right depending on how many hours are on the engine. I guess the pitting is on the valve seats and specialty welding shops can do amazing things.

One thought I had is if the pitting (rusting?) came from coolant leaks the rings may be affected too. If it has fairly low hours the cylinders may be OK but honing and new rings may be advisable--more tear-down though. I wonder if a leak-down compression test might be useful. It might show for certain where the compression loss is happening. At least I've heard of things like listening for air loss into the manifolds with stethoscopes and putting heavy oil on top of the pistons to see if the leak-down slows. If it's all in the head and the hours aren't too high then maybe repairing the head might do the trick without turning it into an oil burner. I would check the valve guide clearances because that can be a source of oil burning and compression loss as well.

Good luck with this and I imagine you have the NH repair manual. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
lsheaffer
Join Date: Jun 1999
Posts: 1082 Northern Illinois
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2004-01-13          73918

I don't think you'll find a complete engine for less than an overhaul. As for finding a Shibaura head , they are like finding hens teeth. If you can fix what you have , I'd recommend it. If it isn't repairable , I'd consider taking it in trade or buying it outright for a parts tractor. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



engine for ford 1710 4x4

View my Photos
taco
Join Date:
Posts: 1
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2004-02-16          77004

Iam also trying to find and engine cross over for a shi... engine to a ford I have a ford 1510 and need a complete engine dealer will only sell it in parts at a cost of about 3500 + sounds to hi for a 16 year old tractor if anyone knows of an engine that would change straight out please let me know call 610-932-5761
....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo


  Go Top Go Top

Share This
Share This







Member Login