Go Bottom Go Bottom

Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-05-30          195248

Hello
Anyone have any ideas or information on how to proceed to troubleshoot and fix a problem with the front wheel drive.The select lever seems to operate something in the gearcase,and with motor off I hear a clicking sound,similar to a switch.But the front wheels do not engage.
Thanks


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
lsheaffer
Join Date: Jun 1999
Posts: 1082 Northern Illinois
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2016-05-30          195249

There is not switch.Jack up one side the front end & see if the driveshaft turns when you turn the wheel. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-05-30          195251

I can see what I think is a universal joint just outside the front differential and that is turning.There is a clamp about halfway down on the driveshaft,would this be the place where I could see if the driveshaft turns as I turn a front wheel?
Once again,thanks
....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
lsheaffer
Join Date: Jun 1999
Posts: 1082 Northern Illinois
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2016-05-30          195252

Check where it comes out of transmission to confirm that all of the driveshaft is OK with the fwd lever Engaged. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-06-02          195294

Hello.I pulled away the driveshaft guard and yes it does turn at the transmission. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
lsheaffer
Join Date: Jun 1999
Posts: 1082 Northern Illinois
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2016-06-02          195297

i'd drain the trans fluid & remove the FWD drop box so I could check the shifter & the gears. ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-06-03          195301

I've found the problem.The splined shaft coming out of the front differential is worn,so the coupling from the drive shaft slips over it.The coupling itself is worn somewhat but most of the wear is on the differential spline.Do you think I have any hopes of finding replacement parts?Thanks ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-06-03          195302

I've found the problem.The splined shaft coming out of the front differential is worn,so the coupling from the drive shaft slips over it.The coupling itself is worn somewhat but most of the wear is on the differential spline.Do you think I have any hopes of finding replacement parts?Thanks ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
lsheaffer
Join Date: Jun 1999
Posts: 1082 Northern Illinois
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2016-06-04          195305

Might be able to find one. What is shaft size & spline count?
....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-06-04          195306

shaft coming out of the differential is not quite 20mm,surely because of wear.The driveshaft is 20mm and the spline count is 14.Can I remove the worn input shaft by just removing the rounded housing or the whole axle has to be dismantled? ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Massey Ferguson 1010 4WD Hydro

View my Photos
dskinner
Join Date: May 2016
Posts: 8 St-Joachim,Quebec
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2016-06-09          195325

Hi.I've taken the front differential apart and have the input shaft out.Do you think that you can get one.There are 14 splines and shaft would be 20mm if thats possible.
Thanks ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo


  Go Top Go Top

Share This
Share This







Member Login