Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

According to the service manual the inner disc has the long portion of the hub toward the flywheel and the outer disc has the long part of the hub to the transmission.

massey ferguson 1040 compact clutch disc
Massey Ferguson Tractors
Replies 3 Post by radarr72

It is shimmed by installing or removing shims under the injection pump. You will need to spill time the engine to determine where you are at. If you have a fax number I can provide you the procedure.

MF 1250 w Iseki diesel
Massey Ferguson Tractors
Replies 3 Post by radarr72

The 1233 only came in one configuration. It has since been replaced by the 1428V. In the 1428v the overrunning clutch has been removed and a duel clutch has been installed instead. The 1433/and 1250 us a hydraulically activated pto clutch to run the pto and have a completely differenty chassis.

1233 Compact Tractor Noise when PTO is engaged and Clutch is mashed
Massey Ferguson Tractors
Replies 6 Post by radarr72

Ok, part number for the op manual is 1449042M1 if it is a gear model and 1449159M2 if its a hydro model.

Crankcase holds: 2.64 qts with filter.
Transmission: gear 3.7 gal of permatran III oil
hydro 4.49 gal of permatran III oil.
Permatran is the Massey name for universal hyd. oil.

Loader capacity could be limited by a number of things. If you oil is milky you need to drain and refill. If it is bubbles then you need to reseal from the suction side of the pump back to the transmission case. It can be sucking air and not leaking fluid. If a packing in the cylinders is blown it would limit the lift capacity, also the loader valve has a relief in it that may be weak or releiving to early.

Hope this helps.

PS> any mF dealer can get you the filters and an op manual.

New to the site have a massey 1010 and have questions
Massey Ferguson Tractors
Replies 28 Post by radarr72

Lets start simple first.

1. Check the fuses in the fuse panel. There are fuses there that won't let the engine crank and also, won't let the engine shut off.
2. Check the seat switch wires for a pinched wire, sometimes they get caught under the seat linkage. Also, check behind the dash, the safety circuit wires sometimes get caught up in the brake return springs.

If the tractor wont crank it makes it sound like there is a ground out in the saftey circuit. The PTO switch or the range switch, or the foward reverse lever if the tractor is new enough could be the problem due to if any of them are engaged you won't get power to the starter from the key.

If you have any more info let me know.

MF1250 elect problem
Massey Ferguson Tractors
Replies 11 Post by radarr72

Had the same problem with my 2N after I upgraded to the alternator kit. I did not have a 12 volt coil and this made it terribly hard to start. It would run and ran good once you got it going. Once I changed the coil to 12v, you just touch the starter and it starts.

ford 2N
Antique Tractors
Replies 7 Post by radarr72

Do you have a Massey dealer close by. They can order you the clutch parts either from Massey or from Hi Capacity. Massey part number for the discs are as follows.

3436797M92 Main disc
3436796M92 Pto disc
3436794M92 Complete clutch assembly

replacement clutch for 1040 compact
Massey Ferguson Tractors
Replies 3 Post by radarr72

Ag tires were 12.4-28 on the rear and 8.00-16 on the front

MF1045 4wd
Massey Ferguson Tractors
Replies 8 Post by radarr72