Tractorpoint Login

print < Tractorpoint Login

Search for =

Topic

Here is what I got.This summer I changed the screen filter and hydro fluid in my tractor (AW32) I also rebuilt the power steering sector and replaced the four loader bucket hydro lines. The 3 point doesn't want to work right and in cold weather it doesn't even want to come up. 30 min warm up time and at high idle it will start to come up. If I raise the bucket the 3 point drops. If I raise the bucket mid way the 3 point works better and doesn't seem to drop off unless I try to use it when the bucket is near the ground. I have a knob to adjust hydro psi under the front seat but now I don't remember where I should have it set. before I did all of this preventive mnt it worked fine. I did remove the screen filter again to insure I didn't miss a plastic plug and the steering sector work great. I rebuilt it because it would drift straight again on a left turn. I don't think this fluid is to heavy for Nebraska weather. Any suggestions?

Farmpro Jimna 2003 2425 tractor hydraulics
Other Tractor Brands
Replies 2 Post by pickinpough

i have a 2003 2425 good tractor but i have a question about the thermostat, i noticed that the thermostat housing had jb weld on it so i decided to order a new one and replace the thermostat while i was at it. the parts manual shows the thermostat under the housing but mine was under the thermostat block? I see a beveled edge on the thermostat block but not sure it i goes between the engine and the thermostat block or the thermostat block and the thermostat housing? makes more sense that it should be under the housing between the thermostat block and not the engine block. can anyone tell me for sure. also best type of antifreeze to use? im sure it has the wrong stuff, looks green.

thermostat replacement
Jinma Farmpro Agracat Nortrac
Replies 1 Post by pickinpough

i have a 2003 2425 good tractor but i have a question about the thermostat, i noticed that the thermostat housing had jb weld on it so i decided to order a new one and replace the thermostat while i was at it. the parts manual shows the thermostat under the housing but mine was under the thermostat block? I see a beveled edge on the thermostat block but not sure it i goes between the engine and the thermostat block or the thermostat block and the thermostat housing? makes more sense that it should be under the housing between the thermostat block and not the engine block. can anyone tell me for sure. also best type of antifreeze to use? im sure it has the wrong stuff, looks green.

thermostat replacement
Jinma Farmpro Agracat Nortrac
Replies 2 Post by pickinpough

Very interesting, I did not realize that the first part of the clutch pedal travel was for the drive clutch. Here I am fully depressing the clutch for shift changes and then part clutch pedal travel for the PTO. The last few replys have been a real eye opener for me!
The dealer said he changed both clutch packs on this tractor before I bought it. I don't know his skill level but some of the other repairs he performed did not impress me. Greg had mentioned something about a stop bolt for the clutch pedal, my pedal hits the floor board so I suspect that it's missing. I haven't verified that yet but I do not remember seeing anything there. You can bet I will correct this.

With this new information, my ignorance to these tractor's operation might be more of the problem than the tractor itself. You guys have given me a detailed mental picture of what to do and what to look for if I suspect a problem exist after I change how I operate this tractor.

My sincere thanks Gentlemen

2003 farm pro 2425 clutch adjustment
Jinma Farmpro Agracat Nortrac
Replies 12 Post by pickinpough

Thanks Greg,

I just ran it up to my shop to drop that drive line and the selector lever broke. I did take the top cover off and remove the lever. I have the parts on order, but I do have one question, I want to drain the oil and flush the trans out, I found a drain plug below under the hi-low part of the trans and removed it. Not much came out and the level in the trans is about the same. Got any ideas? I started to use a suction gun and that will work but I really wanted to clean it out.

Thanks Mike

Farm Pro 2425 Front drive shaft
Jinma Farmpro Agracat Nortrac
Replies 4 Post by pickinpough

Thanks Greg

That confirms my thoughts on how it goes together. Where did you buy the manual that has the front diff and drive line from?

Mike

2003 Farm Pro front differenial
Jinma Farmpro Agracat Nortrac
Replies 7 Post by pickinpough

Rich,

I think I am going to have DAA tattooed to my fore head, I had a dumb ass attack. I screwed in the knob under the front of the seat so the three point would come down slow. Well it did the first time then after that it just held the pressure. I had my blade on the three point so I jacked up the blade to relieve the pressure so I could turn the knob. I bet I only had it out about a half a turn. Once I could turn the knob I set it to 2 1/2 turns. now everything works ok. Thanks again Mike

just bought a farmpro 2425 have issues would like some help
Jinma Farmpro Agracat Nortrac
Replies 17 Post by pickinpough

Thanks again! I sure do like this forum! I'll get down to the parts store and pick some up.

Mike

farm pro 2425 diesel type
Jinma Farmpro Agracat Nortrac
Replies 9 Post by pickinpough