cabs
guest
Join Date: Aug 2017 Posts: 0 |
1999-01-05 740
i am curious if any one can recommend a good hard cab for a new jd4300. what im looking for is one that is fairly easy to remove after winter,since cabs suck in the summer.the jd is used with a brush for snow removal so the cab is almost neccesary to have. we are trying to go through this winter with out one. any replies greatly appreciated.
Reply to | Quote Reply | Add Photo
cabs
DougH
Join Date: Posts: 1 |
1999-01-06 743
Try http://www.curtiscabs.comNot sure how easy there are to remove. But I was wondering the samething. I am about to order a 4300 and wanted a cab for winter that I could remove in summer.
Please post what you find. Or let me know directly.
....
Reply to | Quote Reply | Add Photo
cabs
Craig Wolter
Join Date: Posts: 1 |
1999-01-06 744
I recently installed a Sims cab on my Kubota. I've read message board comments reporting Curtis cabs to be more substantial. However, the Sims appeared to be easier to get into with its rear hinged door, and easier to remove and store. I did not install a heater at first because of the expense. After several weeks of blowing snow, and trying every type of 12v heaters I installed the Sims heater and highly recomend it. The factory phone # is 508-886-6115. They can fax info and refer you to a dealer. Stay Warm! Craig ....
Reply to | Quote Reply | Add Photo
cabs
Jim Boutell
Join Date: Posts: 1 |
1999-01-21 905
I have a Deutz Allis 5251 4wd hydro with badly rusted rear fenders. This tractor was manufactured by Toyosha in Japan in the late 80's. New fenders are no longer available from a Deutz-Allis dealer. Massey Ferguson imported the Toyosha tractors also but in alternating horsepowers. Deutz had 18, 26 and 31 hp. and Massey had 16, 22 and 28. Does anybody know if the 16 or 22 hp. Massey has the same fenders as the 18 hp. Deutz? ....
Reply to | Quote Reply | Add Photo
cabs
Brent Pepper
Join Date: Feb 2002 Posts: 58 Athens Alabama |
1999-01-21 906
Jim,
Call some of the Grey Market salvage dealers and tell them you need fenders for a C174 Hinomoto. Hinomoto was made by Toyosha. The C172 and 174 is the same as the Allis 5015 and DA 5215. I hope this helps.
Brent Pepper
....
Reply to | Quote Reply | Add Photo
cabs
Chris
Join Date: Posts: 1 |
1999-01-21 907
I looking at a John Deere 4100 HST. I was wondering how much it would cost to buy. I would also need a loader, 60" mid mower.Can I attach my Snow thrower and log splitter that I have for my JD 430?If not how much for a snow blower for the 4100?Any help would be appreciated. ....
Reply to | Quote Reply | Add Photo
cabs
Jim Boutell
Join Date: Posts: 1 |
1999-01-21 908
I have a Sims cab on my Deutz-Allis with the heater and am very satisfied with both the quality of the cab, it's fit, ease of installation and removal, warmth, and visibility. I would recommend Sims. ....
Reply to | Quote Reply | Add Photo
cabs
Jim Stone
Join Date: Posts: 1 |
1999-04-17 2986
Where would I find some information on sims cabs? I need one for my Ford. ....
Reply to | Quote Reply | Add Photo
cabs
Barry Ratcliffe
Join Date: Posts: 1 |
2000-07-18 18066
If your local NH dealer doesn't have info, e-mail me or reply here with your mailing address and I'll send you information
Barry Ratcliffe
Plant Manager/Sims Cab ....
Link:
Click Here
 
Reply to | Quote Reply | Add Photo
Go Top
Share This