Nortrac NT304C 4wd shifter stiff stuck
sjrogers1
Join Date: Aug 2007 Posts: 36 Arkansas |
2007-08-09 144506
We have a NT304C. The 4wd shifter has been real hard to shift, sometimes impossible. I have the shifter out now and will be taking it to a machine shop to hopefully modify and fix. With lubrication the shifter will again move. Any suggestions?
Steve
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
greg_g
Join Date: Jan 2004 Posts: 1816 Western Kentucky Pics |
2007-08-09 144513
Northern sells a confusing spectrum of tractors. Is your lever connected by cable or connected by conventional finger and fork ?
//greg// ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
sjrogers1
Join Date: Aug 2007 Posts: 36 Arkansas |
2007-08-09 144553
Coventional lever connected to a fork.
Steve ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
greg_g
Join Date: Jan 2004 Posts: 1816 Western Kentucky Pics |
2007-08-09 144565
I don't have access to the manual right now to confirm this. But if your gear oil level is correct, that mechanism should get sufficient splash lubrication. Check the pivot for binding. Alternatively, the finger could have jumped out of the fork. Depending upon which side it jumped out on, it could be binding the fork on the rail.
The rails themselves should have detentes; one for forward, one for reverse. It's typically a spring-pin-ball arrangement where spring pressure holds the ball in a rail detent. Sometimes the ball will drop behind the rail and jam it up.
//greg// ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
sjrogers1
Join Date: Aug 2007 Posts: 36 Arkansas |
2007-08-11 144617
The shift mechanism is intact. No parts out of place. I can move the shifter with a lot of effort. Does it help to shift with the tractor in motion? I'm having a machine shop take the shift mechanism apart. He may drill an oil passage into the spring and ball passage, don't know what he will decide.
Steve ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
greg_g
Join Date: Jan 2004 Posts: 1816 Western Kentucky Pics |
2007-08-11 144618
Ok, I understand the problem now. Engaging the front diff with that lever is no different than engaging the diff lock. The wheels must make sometimes as much as one quarter revolution before the respective engagements take place.
So yes, engage the front diff with the 2wd/4wd select left while the tractor is moving slowly in either direction. It's permissible to turn the steering wheel while doing this. When engaging the diff lock though, it's important to keep the tractor moving in a straight line - or driveline damage could occur.
//greg// ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
sjrogers1
Join Date: Aug 2007 Posts: 36 Arkansas |
2007-09-25 146073
I took the shifter apart and replaced the shifting fork. The tractor now shifts as it did when new. The shifting fork had some wear marks.
Steve ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
earthwrks
Join Date: Dec 2003 Posts: 3853 Home Office in Flat Rock, Michigan Pics |
2007-09-25 146082
The worn fork, to me, is a cause for concern. I would expect it to happen again, and probably sooner now that the oil is laden with metal particles. The gear is likely poorly machined and has, and will be, chewing up the new fork. That means you'll have metal filings-contaminated oil from both forks. I suggest you change the hydraulic filters and the fluid. Otherwise, you will likely have pump wear/failure in the near future if the filter media isn't doing it's job (goes into bypass) or the micron size is large enough to allow contaminates to pass. For example, the wear you saw on the fork...the inside of the pump may look like that too. ....
Reply to | Quote Reply | Add Photo
Nortrac NT304C 4wd shifter stiff stuck
chipuren
Join Date: Jul 2003 Posts: 193 Arkansas |
2007-09-28 146189
More likely the fork got slightly bent trying to engage the front wheel drive. once bent the forks stayed rubbing on one side of the grove in the sliding gear. NO worry with hydraulic filter as the oil in the transmission has nothing to do with hydraulics, no pumps to worry about either. it is a simple splash lube. Most of these tractors have a magnet at the bottom to collect metal fragments, but not sure on this 304 assuming it is jinma. we have seen a couple of 2430 Farm pros with stiff shifting front wheel drive and new forks cured them. ....
Reply to | Quote Reply | Add Photo
Go Top
Share This