Can you run 540 RPM implements on high speed PTO at half Throttle
yocsr1
Join Date: Dec 2013 Posts: 182 Terre Haute, Indiana Pics |
2014-03-27 189814
I have two speed pto on the Foton I just bought. All my equipment is 540 and I know on my old Ford I didn't hit 540 until I was at 3/4 throttle. Can I run the 540 equipment on 1000 with my rpm down around 1100? I'm just thinking easier on the motor and less fuel consumption. Any thoughts. Larry.
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
candoarms
Join Date: Mar 2007 Posts: 1932 North Dakota Pics |
2014-03-27 189815
Larry,
For the most part, the answer to your question is, "No".
Most of your implements (mowers and tillers) likely require more torque than your engine will produce at 1/2 throttle. You'll find that your engine will begin lugging. This creates tremendous heat, which will quickly destroy your engine.
There are a few exceptions to this rule.......
I have a dual rear PTO available on my Kubota B2920. I use the 960 rear rpm when cutting firewood with the cordwood saw. With a sharp blade, the horsepower requirements are quite low. I'm able to cut a whole lot of firewood with the tractor running at 1/2 throttle.
The same is true for my PTO generator. When welding, the demand on the generator is quite low. I'm able to run at 1/2 throttle at 960 rpm, producing plenty of power to run the welder. However, if I were to attempt to power my house, during a power outage, the demand on the generator would be quite high, requiring more power from the tractor than it would provide at 1/2 throttle.
Hope this helps.
Joel ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
greg_g
Join Date: Jan 2004 Posts: 1816 Western Kentucky Pics |
2014-03-28 189816
Quote:
|
//greg// ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
yocsr1
Join Date: Dec 2013 Posts: 182 Terre Haute, Indiana Pics |
2014-03-28 189817
Ok. I was just curious. I saw a video of a guy who does a lot of brushhogging and he said he runs his pto at 1000 with rpm's around 1100 which is pretty much lopping along and say's he runs all week on 5-6 gal. of fuel. I had never heard of this before so that's why I was asking. I run the old Ford 8-10 hrs. wide open when I'm mowing and wondered if this would be better. I just got the Foton so I haven't mowed with it yet. Larry. ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
kthompson
Join Date: Oct 2005 Posts: 5275 South Carolina Pics |
2014-03-28 189824
I am asking here but if your tractor had two speed PTO and was a good bit larger in HP than the implement you are using, would it then maybe work?
A second question, there are implements made for 1,000 PTO speed. Is this not what that is for?
Is not the splines on the two PTO shafts also different to help prevent using the wrong speed PTO? ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
candoarms
Join Date: Mar 2007 Posts: 1932 North Dakota Pics |
2014-03-28 189826
Kthompson,
My new Kubota has a two-speed rear PTO. There's only one output shaft, with the standard 540 rpm 1-3/8" 6T spline adapter. I can connect any 540 rpm implement and run it at 960 rpm.....but I don't do that with most implements.
Snowblowers, tillers, mowers..etc....require max power from the tractor. I use the 540 rpm for these implements, while running the engine at full throttle.
Yes, you could put a 4 foot rotary mower behind a 60 hp tractor and power it with the 1000 rpm output, while running the tractor at half-throttle, but you'd make several more trips around the yard before finishing.
After totaling up the additional hours on the tractor, as well as engine oil changes and other maintenance items, I don't really see any savings........or what little savings there would be wouldn't amount to much.
Joel ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
greg_g
Join Date: Jan 2004 Posts: 1816 Western Kentucky Pics |
2014-03-29 189838
Quote:
|
That mark on the tach applies for all available PTO speeds, that's the way the PTO system is engineered. But a vast majority of the implements made for North American CUTs are engineered to operate most efficiently at 540. Using engine revs lower than that mark may result in your operating too low on the engine torque curve. If the tractor and implement are otherwise matched in size, this causes premature wear and tear on the tractor over the long run. Plus, it then becomes pure guesswork whether or not the implement is operating inside it's own design speed.
//greg// ....
Reply to | Quote Reply | Add Photo
Can you run 540 RPM implements on high speed PTO at half Throttle
kthompson
Join Date: Oct 2005 Posts: 5275 South Carolina Pics |
2014-03-31 189864
A few years back I sold a peanut combine which was pulled by and used the tractor's pto for power. I had used it for green peanuts which is harder work than dried peanuts and the person buying it for green peanuts. A couple of weeks into his harvest he called me upset it was doing a poor job and in talking found out he tried to run it not using the std 540 pto speed, was using something like eco PTO or something his JD had. My instructions were simple, you must run that combine with full 540 rpms with plenty of power, must have solved his issue for last heard from him. ....
Reply to | Quote Reply | Add Photo
Go Top
Share This