Tractorpoint Search for

tractorpoint.com - The leader in Tractors from Compacts, to Utility, to Full Size Tractors! Kubota, John Deere, New Holland, Kioti, Case/IH, and Others. Keywords=Compact Tractor, Kubota Tractors, Kioti Tractors, JD, John Deere Tractors, New Holland, Case Boomer, Used Tractors, Classifieds, Dealer Directory, Tractor Pictures / Images

parts | discussion | photos | podcast | reviews | specs | dealers | classifieds | contact | faq | myProfile | home Login Now | Sign Up

Search for =

Topic

I just had my driveway done - The first 1000 feet were pretty gentle slopes, with 2 culverts and build up in the crossings of the draws where the culverts are. The last 650 feet are in boulder strewn foothills, and took some work.

I had a minimum 12' wide road cut, and needed some blasting (in the boulder area) and my excavator, also my neighbor, charged me almost $15000, plus another $8k for putting down 7" of pit run on it. This included compaction, etc before the final grading and pit run. Even before pit run, I ran 20+ cement trucks over it without rutting - A tribute to the dirt work, since the exsisting road leading to my drivway didn't fair as well.

My geography tends to be expensive, but I did get a pretty good deal. Other excavators were charing about $1 per square foot of road space, excluding pit run.

Advice Needed - Gravel Driveway Construction
Garden and Landscape
Replies 22 Post by HuckMeat

Sounds like you need to speed up the engine RPM to match the task better. What engine RPM do you run when things work normally in low/medium, and are you adjusting it for the different task? I usually run about 2400 or so for loader work, a point that keeps the engine from lugging but gives me good workability. I suspect to go fast I'd need to raise that, plus the range lever change.

KUBOTA HYDRO RANGE
Kubota Tractors
Replies 20 Post by HuckMeat

HELP!A rat chewed my wiring harness and I need to remove the steering wheel to repair it How do you get it off? I see no holes for a steering wheel puller.

STEERING WHEEL REMOVAL
Kubota Tractors
Replies 2 Post by bruiserbruce

The 110 is pretty powerful, both loader and hoe. They did a good job designing it. It drives like a skid steer, very fast and agile. Alot of times I can turn it by sliding the front end sideways when going in reverse and then hit forward while in a turn. It sure does alot of work in a day. Put in 7 hrs today, looks like I'm working tomorrow too. I got rear foot controll hydraulics because I put on a thumb and might get a hammer $8500.00 ouch, quick release hoe bucket, and a skid steer quick disconect hd front bucket. Only thing I wish I got and recomend is front hydraulics run through the joy stick with a switch to run front or rear implements with the stick, say a angle on a blade or a sweeper on front. It all adds up though, near $50,000.00 just for what I got.

Cabot Stain vs Benjamin Moore
Home Improvement
Replies 7 Post by lucerne

Redman
The more information you provide the more detailed the estimate. I believe that tractor you are asking about was made between 1985 and 1991. I guess $5500, plus or minus a 1000.
Hope this helps.
Rex

B7200HST value
Kubota Tractors
Replies 2 Post by rexbeach

are you sure the hydraulics work off the Transmission fluid, I have a long and mine works off the fluid in the rear axle

Long 460 hydraulic problem
Long
Replies 10 Post by loghouse95

StoneGate:
I am in the final stages of purchasing an L3130. I plan to use a 6' LandPride rear finish mower. I have a 4' LandPride RFM now that I have used for years. Keep the blades sharp and the quality of cut is excellent. That is one of the delays, the pricing on trading the current RFM. I expect to be able to mow close enough to the buildings and plantings that I can finish with a weedeater or the DR Trimmer/Mower. I am setting the L3130 up so I can do 90-95% of my work from the tractor seat. An L3130 with a FA723 loader with Quick Attach, pallet forks for the loader plus a grapple kit and tooth bar. I am convinced that it will do everything I plan on.

Tractor and Z Mower or just Tractor
Kubota Tractors
Replies 11 Post by texbaylea

Pardon my ignorance.... but what is the "power-beyond optional kit"? Thanks...

Want backhoe for 7275 What s compatible
Cub Cadet
Replies 7 Post by rozett

That's sort of what I was thinking. The fact that a chipper jam caused the tractor to stall indicates that the chipper won't tear itself apart so something else has to give. Maybe that something else would be expensive to fix. Which brings me back to my original question, how can I add a shear bolt to the pto driveline? I know you can buy add-on slip clutches but this situation shouldn't happen very often so a cheap fix is appealing.

Dumb shear bolt questions
Operating and Attachments
Replies 19 Post by kwschumm

Using Delvac 1300 Super 15-30 in the Dodge Cummins HO truck engine, one diesel car and wanted to know if it was suitable for use in the JD 2355 MFWD tractor and the Kubota B8200 diesel. Had been using straight 30 weight but it is a bit thick in winter last year. I was told this 15-40 oil was suitable for year round use, but would strip a good deal of material off the piston and various surfaces, but after an early oil change, it would be fine. There are only about 300 hours on the 2355 and about 600 hours on the Kubota B8200. Basically would like to use this oil for both diesel trucks, one diesel car and both tractors and get it in 55-gallon drums.

Delvac 1300 Super 15-30
Parts and Repair
Replies 3 Post by Terry Joe Sprinkle

It seems a strange thing to be telling most customers--especially those who don't have repair manuals. I really don't think I'd try this without a manual. I'd also be aware that some drives may have parts that could come off the end of the shaft and drop into the cases.

If the tractor has HST the drive may be simpler than ones used with the gear TX's for which I have manuals. There is no procedure in my manuals for the removal and inspection of the output shaft separate from general overhaul procedures. However, it does look possible from my parts diagrams. Most PTO output shafts would have a snap ring immediately behind the oil seal as well as several other interior snap rings and retaining rings. Assuming the service manager knows a procedure, it almost certainly would require the removal of at least an outer snap ring. I can't tell from my parts diagrams if removal of interior snap rings would be necessary and if so whether they'd be accessible.

Let's assume that the service manager knows his tractors but maybe should have told you more detail or maybe not made the suggestion at all. He'd probably tell you if you need a new gasket.

TC29 PTO
New Holland Tractors
Replies 3 Post by TomG

Just purchased a JD 4115 410 FEL 53" bucket (two hooks) w/LX5 rotary cutter (slip clutch), Turf Tires, I-match, & ballast box.... Expect delivery next month. Cash deal $18000.00

JD 4115 Pricing
John Deere Tractors
Replies 9 Post by paluvsjoshua

Greetings
If anyone is still reading this thread here is the follow up. $146.51 , 100 for pickup and rtn mileage. 35 for labor and 10 for some tranny fluid. Everything works. Hose actually looks new as does clamp. Thanks for all the input, it really does help.
Sincerely
Tracer

Jerky Fel main boom
John Deere Tractors
Replies 12 Post by tracer

Please respond to the other post! Duplicate Post!

Cabot Stain vs Benjamin Moore
Home Improvement
Replies 1 Post by ncrunch32

I like the analogy -- my parents never had AC in their cars, so I didn't either until I got married -- and I cannot imagine not having it now! Every dollar I spend on a mower is a dollar less for a tractor and implements -- but I do feel the need to look at and for a mower with hydro.

And in terms of buying a mower that has been used commercially, I'm hoping to find one that was used by a reputable, local firm. It seems that if someone is making a living off his mower, he ought to be maintaining it on a regular basis. And buying from a dealer will make me feel better, as at least the dealer will have gone through the machine and is willing to stand by it for at least 30 days. Because I am not that mechanically inclined I am not too comfortable buying used equipment from a stranger. I've seen how some of my friends maintain things(or don't, as the case may be)...

Lawn mower
Kubota Tractors
Replies 25 Post by Oliver

Here is what happens to mine. The left rear arm for the 3 point controls the mower deck raising up and down. With your knob in the install position, lower your 3 pt. all the way down, from the right side of your tractor, raise it back up while pushing out on the left arm of your 3 pt. with your left leg (This is like twister). As it raises up you will see that the arm catches a mechanisim which is connected to an 18" long bar that is threaded on both ends (it is on the left side of your tractor just inside the rear wheel. That will allow the deck to go up. Now that it is all the way up, you will be able to set the height that you want on the knob. This is the only time that you can adjust the height. Attempting to do so while deck is not all the way up, will only lead to headaches, and a broken plastic knob. To avoid using this twister method, you can stick a bar across the lower arms and be done. Hope this helps

JD2210-Installing a 54 quot Mower Deck
John Deere Tractors
Replies 3 Post by BH3131

A lot of it depends on what you need the tractor for at your new house. If you're just mowing a small suburban lot then a dedicated mower may be better suited to your needs.

Trade
Kubota Tractors
Replies 7 Post by kwschumm

Yooper! Thanks for looking into this! The order is on its way and I am looking forward to using my receiver hitch to pull my boat and utility trailers around. Bad River is, in fact, very responsive!

Receiver hitch for iMatch
John Deere Tractors
Replies 82 Post by ncrunch32

Can anyone tell me if there is a site for Long manufactured<br>
implements. I would like to know the lengths of the blades<br>
so hopfully I can find some universal blades so I don't have to wait on ordered ones.<br>
<br>
Thanks<br>
Big Hump

Long 5 finish mower
Mowers Field and Finish
Replies 1 Post by Humpty

Jim,

I already have sent you the PDF to the email that is in your profile.

Greg

An Orange Machine in the Neighborhood
Kubota Tractors
Replies 38 Post by murphyg