Go Bottom

Jubilee tractor and rototiller

View my Photos
mustang
Join Date: Jul 2003
Posts: 2 South Carolina
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-18          53359


Iwas told that rototillers didn`t work well with the older tractors like the ford jubilee. Is there any truth to that?



Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
Peters
Join Date: Feb 2002
Posts: 3034 Northern AL
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2003-04-18          53360


There are 3 factors that effect the performance of these tractor with the tillers. First not all have 3 pt hitches as they were an option and a lot of people did not have 3 pt implements so...
Most were sold with a single stage clutch so the PTO stops as you stop the tractor. For tilling it is much easier to start the tiller before you enter the row.
The other problem is that you need about a 6 ft tiller to cover the tracks of the tires. The 25-30 HP at the PTO is a little light to spin such a big rototiller. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
DK35vince
Join Date: Feb 2002
Posts: 689 Western,Pa.
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-18          53368


Another problem could be gearing.
My brother has an 8n ford.( I think its an 8n) with no low range.
It is geared far to fast in its lowest gear for tilling. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
TomG
Join Date: Feb 2002
Posts: 5406 Upper Ottawa Valley
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-19          53389


I don't know if tillers with offsets are available but an offset might solve the width/power issue. Ground speed may be an unavoidable problem. I was surprised to learn that a mystery lever on a Yanmar was a creeper, and creepers are standard features on some models Yanmars. Apparently ground is worked almost exclusively by tillers in Japan. Creepers are considered almost essential because of the very low ground speeds they provide. I could use something slower than my lowest reverse at .8 mph at pto rpm when blowing deep snowfalls. I imagine something slower would be good for a tiller if I had one but creepers were an option for my Ford. I imagine my ford 1710's lowest reverse is slower than the 8's are. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
AMP762
Join Date: Jul 2003
Posts: 4 SC
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-22          53598


We once tried my tiller behind my brothers TO20 Ferg.it didn't work at all.I believe if the tiller rotated backward it would work. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
Stan in Calif
Join Date: Feb 2002
Posts: 47 Sacramento Valley- Glenn County
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-23          53629


There was on option called the Sherman Transmission- that would probably work. Otherwise, no. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
mustang
Join Date: Jul 2003
Posts: 2 South Carolina
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-04-23          53660


Thanks for your responses.It`s been a big help. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
marklugo
Join Date: Jul 2003
Posts: 281 Tifton, GA
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2003-04-28          53936


If you looked into the 601 and 801 series and later similar models, you probably yould have a good match. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Jubilee tractor and rototiller

View my Photos
pmhaas
Join Date: Dec 2003
Posts: 3 Pine Island MN
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2003-12-21          71885


The replies you have received are right on the mark. The ideal tractor would have an independant PTO and much lower gearing than the Jub has. There are several who claim satisfactory results with the old Fords by making several shallow passes with a tiller, but most feel that if the garden is big enough to cost justify a 3 point tiller (versus hiring it done or even a big Troy Bilt) it is probably big enough to plow and disc. A Jub will plow and disc all day long and never complain. In my case I have an 8N and an 850 (so no horsepower concerns)and would not even consider a 3 point tiller because soil has so much clay it would take a huge number of passes to get acceptable results. ....


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo


   Go Top


Share This







Member Login