Third Selective Control Valve: Tractor Implements  -- Tractor Attachments Implements 3ph Discussion Forum and Review Third Selective Control Valve: Tractor Implements -- Tractor Attachments Implements 3ph Discussion Forum

  parts   |   manuals   |   discussion   |   photos   |   podcast   |   reviews   |   specs   |   dealers   |   classifieds   |   contact   |   faq   |   myProfile   |   home          Login Now | Sign Up


FAQ:   What is a tractor?

Forum Index
New As Posted | Active Subjects



www.emerichsales.com - New & Used Equipment
          View Tractors For Sale!


www.partsbynet.com - Lawn and Garden Equipment Parts


Bernardsville Landscape Lighting
Click to Post a New Message!

Discussion Boards > Active Subjects > Messages as Posted > Tractor Implements Forum

Page [ 1 ] |
Reply | Pop Up Window Reply | Add PhotoAdd Photo
 12-06-2000, 07:21 Post: 22160
Ken



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1
 Third Selective Control Valve

What can the third scv be used for? Thanks Dixy






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 12-07-2000, 05:15 Post: 22193
TomG

TP Contributor

Join Date: Feb 2002
Location: Upper Ottawa Valley
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 5406

2
Filter by User
 Third Selective Control Valve

I take the question to mean; two valves for a loader (lift & bucket curl) and what would is a 3rd valve used for? A third valve usually supplies a circuit to the rear of a tractor. In my case, I use the rear circuit to feed a backhoe, power chute for a snowblower, and hydraulic top-link for a box scraper and pallet forks. In the case of the pallet forks, I need two circuits, one for the carriage and another for the lift. Since I only have one circuit, I have to run the carriage tilt from the loader curl circuit. If the forks had side-shift, I'd need a third circuit. There are plenty of applications for rear hydraulic circuits, and some people have elabourate setups. Three circuits just for rear hydraulics isn't a bad setup. One for top-link, another for side-levelers and the third for 3ph implements with hydraulics.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 12-07-2000, 07:00 Post: 22198
MJB



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1
 Third Selective Control Valve

On JD 4000 series tractors other than the 4100 the 3rd SCV is also typically used to raise the mid mower deck. If you want to keep your FEL attached and operational at the same time as your mid mower you will need the 3rd SCV. I think that the 4100 uses the TPH to raise the mower.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 12-07-2000, 23:15 Post: 22222
Mike S.



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1

2
Filter by User
 Third Selective Control Valve

My 3rd SCV controls the cylinder used to raise and lower my belly mower. Would it be possible to use the 3rd SCV hydraulic connectors at the back of my 4400 Deere to attach to a hydraulic top link on my 3 pt? (assuming I would first disconnect the hydraulic lines to the belly mower's cylinder) Would I need any additional hardware except for the hydraulic lines and cylinder? Mike S.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 12-08-2000, 07:33 Post: 22226
TomG

TP Contributor

Join Date: Feb 2002
Location: Upper Ottawa Valley
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 5406

2
Filter by User
 Third Selective Control Valve

I'm guessing that grabbing the mower circuit to run a top link wouldn't require anything except quick connectors and long enough lines. I mentioned that I have to grab my curl circuit to run both the forks and top-link for the carriage tilt. I ordered the cylinder with lines long enough to run from the 3ph area to the loader valves. The only complication I had was that the cylinder came with CAT2 loops. Sleeves were supplied to size the loops to CAT1, but the sleeves were too long to fit in the top link bracket on the tractor. The dealer sent new sleeves, although I could have ground the old ones down if I wasn't worried about taking the temper out.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 03-22-2001, 09:05 Post: 25732
Tree Farmer



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1
 Third Selective Control Valve


I have ordered My 4300HST with the 430 FEL, and 72" belly mower, and a 3rd SCV.My Question is this, should I order NOW while it is being put together the extra SCV and outlets for Hydraulic lines on the rear of the tractor for future needs? Also if I do, where do they put the lever?Anyone?






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 03-22-2001, 09:19 Post: 25733
Mike S.



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1

2
Filter by User
 Third Selective Control Valve

If there is any chance that you will need the hydraulics at the back (such as a hydraulic top link to your 3pt), then you should consider having them added--it is not real expensive as I recall. The lever will be mounted in the top of the right fender where the black blank is currently located. Unless JD has changed the design, you will learn to grab the lever itself and not the black knob since the knob tends to come off when grabbed. Mike S.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 03-22-2001, 11:32 Post: 25743
JeffM



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1
 Third Selective Control Valve

Tree Farmer, I agree with Mike on this. Order it now and be done with it. I ordered a 3rd SCV on my 4400 last year and it wasn't very expensive. It is a pain to install on your own because you have to remove the right rear tire to install it. I haven't had trouble with the knob on mine yet - we'll see how it holds up after a season of using it to lift and drop the belly mower. I expect to be using it for a hydraulic top link also.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

 03-24-2001, 09:48 Post: 25807
Norman Grinnell



Join Date:
Location:
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster
Posts: 1
 Third Selective Control Valve

Jeff, I just finished installing a 3rd SCV on my jd4600 and it is not necessary to remove the left rear tire. The installation took me about 6 hours total. The directions are very good. If purchasing a new tractor have it ordered with it as the cost is about the same as I paid for the kit.






Reply to PostReply | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo




Bookmarks: Digg It | Del.icio.us | Technorati | Furl | Stumble This

Reply | Pop Up Window Reply | Add PhotoAdd Photo


Page [ 1 ] |

Discussion Boards > Active Subjects > Messages as Posted > Tractor Implements Forum

Thread 22160 Filter by Poster:
JeffM 1 | Ken 1 | Mike S. 2 | MJB 1 | Norman Grinnell 1 | TomG 2 | Tree Farmer 1 |




Most Viewed

+ Tractor Category 1 2 3 Hitch sizes Defined
+ What is 3 point hitch draft control?
+ Howse impliments are junk.
+ Farmi vs. Fransgard Logging Winch
+ Spike tooth drag/harrow
+ Rock picker
+ Tractor Implements Category 1 vs Category 0
+ Kubota rear hydraulics for a log splitter
+ Road-Boss-Grader
+ Box Scraper size

Most Discussion

+ Newbie needs help - box blade
+ Hydraulic actuator (ram)
+ Anybody ever used a Stickler?
+ 3ph assembly for JD 4200 - Nic
+ Post hole diggers
+ Tire Fluid
+ Need a grapple rake for my FEL
+ Small farm tractor attachment
+ Box Scraper size
+ Log Skidding

Newest Topics

+ Leinbach L7200 Post hole digger oil seals
+ Pull type box blades
+ Hydraulic Top Link
+ Speeco 3pt. log splitter
+ Quick Hitch
+ Woods RM59 finish mower
+ Fiberglass thank fittings
+ Best Tractor Implement vs Worst Implement Investme
+ Proper Engine RPM When Using Lift
+ Rebuild PTO pump?







Turbochargers for Tractors and Industrial Machines
Cab Glass for Tractors and Industrial Machines

Alternators for Tractors and Industrial Machines
Radiators for Tractors and Industrial Machines

Driveline Components for Tractors and Industrial Machines
Starter Motors for Tractors and Industrial Machines