Go Bottom Go Bottom

Rebuilt FORD 1710 low oil pressure

View my Photos
jhaems
Join Date: May 2007
Posts: 9 Minneapolis, MN
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2007-05-07          141904

I have a Ford 1710 compact tractor with a 3 cylinder Shibaura diesel engine built between 1983 - 1986 (ID: XUL 00704; Model: AL3136; Unit: 305B; Engine: SN# H843 18754)

The engine threw a rod through the side of the block. I got a used block that was mag tested, new crank, oil pump, bearings, etc. and we can not get the oil pressure above 27psi (spec is 37-57).

We have consulted with numerous people for some reason that would account for the low pressure. We have tried everything anyone mentioned... so I think we've covered the obvious.

Do you know anyone with experience rebuilding these engines? This is the third engine in this tractor and I'm wondering if there might be something unique about this engine that we don't know about. We had the Ford repair manual which was helpful, but not on this issue.


Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
mtnpapa
Join Date: Feb 2009
Posts: 5 Highlands,NC
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2009-02-12          160245

Do you still have your 1710 and is it a 4wd? ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
jhaems
Join Date: May 2007
Posts: 9 Minneapolis, MN
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2009-02-12          160250

I still have it and it is a 4-wheel drive.

We figured out what the problem was. When the engine "blew" part of the piston arm hit the oil pickup tube. The tube is connected to the oil pump via some kind of pressure connection. The impact pulled that tube out about 1/8 inch or so, but you could not tell it by looking at it.

So I have $5000 into the new engine, but when the guy brings it back, apparently the throw-out bearing had rusted or something, so now it screams when you put the clutch in. I have a diesel mechanic moving onto the property and he will get it running again to use on the property.

Also have a John Deere 450C bulldozer with a reverse problem and a hose blew draining all the hydraulic fluid out so I can't lift the blade up.

It's true ..... our stuff owns us. Thanks.... ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
kthompson
Join Date: Oct 2005
Posts: 5275 South Carolina
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2009-02-13          160259

It's true ..... our stuff owns us. Thanks....


Never heard it worded that way but certainly understand it. Buy and use one machine and the support it needs is a shop, tools, a service truck, fuel tanks, insurance, place to use it, more equipement to support it, and all you wanted was to dig one little hole or cut a small lawn. :-) O

Ole Tim the Tool Man knew the feeling.

....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
candoarms
Join Date: Mar 2007
Posts: 1932 North Dakota
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster  View my Photos  Pics

2009-02-13          160260

I hope nobody minds if I post an opposing view. The following is from one of my favorite characters in U.S. History.....Lysander Spooner.

"Men are able to produce almost no wealth at all by their hands alone. Until they make discoveries in science, and inventions in implements and machinery, they remain savages, few in number, and living upon such wild fruits as they can gather, and such wild animals as they can kill."

Joel ....


Link:   Lysander Spooner -- Universal Wealth Easily Obtainable

 
Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
mtnpapa
Join Date: Feb 2009
Posts: 5 Highlands,NC
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2009-02-13          160269

Thanks for the reply. I have a shibaura sd2640 which uses the same parts as your 1710. I messed up the connector in the front axle which enable the tractor to operate in 4wd. I'm looking for a used part to replace it if you decide to "part out" your tractor.

Thanks ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
jhaems
Join Date: May 2007
Posts: 9 Minneapolis, MN
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2009-02-13          160289

Try.... Weaver's Repair, Compact Tractor Parts, 9507 Forest Ridge Rd., Shippensburg, Penn. 17257 - ph 866 950-1050 or 717 477-9332; fax: 717 530-9705

Website: www.compactractorparts.com

They had everything I needed except the pickup tube. They were the best spot for compact tractor parts... and as you probably know, finding parts for this "domestic" FORD is very difficult... since nothing about the tractor was made in the US... so much for buy American. Good Luck.... ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo



Rebuilt FORD 1710 low oil pressure

View my Photos
mtnpapa
Join Date: Feb 2009
Posts: 5 Highlands,NC
TractorPoint Premium Member -- 5 Tractors = Very Frequent Poster

2009-02-14          160298

Thanks for ALL the info.!! I'll check him out. As you said, parts are hard to find and expensive! ....

Reply to | Quote Post Reply to PostQuote Reply | Add PhotoAdd Photo


  Go Top Go Top

Share This
Share This







Member Login